Automatic Technology Australia Securalift GDO 2v4 Instructions d'installation et manuel du propriétaire - Page 14

Parcourez en ligne ou téléchargez le pdf Instructions d'installation et manuel du propriétaire pour {nom_de_la_catégorie} Automatic Technology Australia Securalift GDO 2v4. Automatic Technology Australia Securalift GDO 2v4 19 pages.

Imprimer la page
17.2
DE,LE,TING
THE TRANSMITTERS CODE FROM THE CONTROLLERS RECEIVER.
If
you only want
to
delete one
transmitter code
stored
then use step
17
.2
(a) to (d) if
you want to remove all
codes
then use
(a)
Select
the transmitter(s) you want
to
delete
from the
memory.
(b)
Press
and hold the
Door
Code
Button on the
Con-
trol
Panel
(ref: Fig
17).
(c)
Press
the transmitter button you want
to
delete
for
approximately
two
seconds. Pause
for two
seconds.
Press
the
transmitters button again
for
approximately
STEP
18
INSTALLATION
OF TRANSMITTER HOLDER.
(a)
Mount the holder
in
a location out
of
reach
of
ch,*ien
and
convenient to the customer.
(see
Fig
19)
(b)
To
operate
the door, Code button one of the trans-
mitter or
any
button you want
as
per
Step
17.
(c)
To
operate
the light function only, Code button
two of
the
transmitter or
any
button
as
per
below.
(d)
Press
and
hold the
Light
Code
Button.
(e)
Press
the transmitter button you require to operate
the light
function
for
approximately
two
seconds.
Pause
for two
seconds. Press
the transmitter Button
again
for
approximately
two
seconds
(f)
Release
the
light
code
button
(g)
Press
the Transmitter button
selected
to
operate
the
light function
and
see
if it
operates
the
light only
STEP 20
SETTING
OF
AUTO CLOSE MODE
AI'\
TIME
IN}TORTANT NOTICE: A PHOTO ELECTRIC
BEAM MUST BE INSTALLED WHEN USING
THE AUTO CLOSE MODE.
The
Auto
Close
timer
will
only start after the Photo
Electric
Beams
(P E ) path is broken.
If
the P
E
path
is not broken the door
will
remain open
till
the path
is broken.
If
the Door Opener incurs an obstruction
(not from the P.E.) while closing the door
will
re-
open and
not auto
close.
SETTING AUTO CLOSE
TIME
(a)
Press
in
and
hold the
Auto
Close
Time button
(J
in
FIG
20)
(b)
While holding
in the
Auto
Close
Time button,
press
the green Open button @ in FIG. 20). Each
press
of this button
will
add 5 seconds
to the
auto
close
time.
(c)
To
decrease
the
time
follow
step
1
and
press
the
red Close button. Each
press
will
deduct 5
seconds
from the auto
close
time
(e) Turn the Power
Off to
the Drive Unit.
(f)
Press and
hold the Door Code Button on the Control
Panel
(g) Turn the Power back on
again
(h)
Release
the Code
Set
Button
after three seconds.
A11
the
stored codes should be
now
deleted. Confirm
this
by
trying to
operate
the door by pressing one of the
deleted
@..@.
@@'
PRESS
AND HI
G__--
r
:H,@
:H:
@
cAULI
UN
TI]1:
UNIT
]S
N[T
UStR StRV]CIABLI
]]
I
SCEI'']t.T P!\,vtR SUPFLY
BtIt]Rt
RtI'41]V
l
NG Ct]ViR
trr,
\
.
''Jltut-'..
'
Page
12