Astria Fireplaces Rhapsody54 Series Panduan Petunjuk Instalasi - Halaman 8

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Aksesori Perapian Astria Fireplaces Rhapsody54 Series. Astria Fireplaces Rhapsody54 Series 12 halaman. Linear direct-vent fireplaces accessory kits

Halaman Cetak

Gather and reseal all wiring

1. Gather all wiring and pilot connections together at the end

of the slot, and reseal with high-temperature sealant, such

as Mill-Pac

(not provided) (Figure 7).

2. Reposition the right burner bracket and secure with the

three (3) previously removed screws; tighten the fourth

screw (Figure 7).

3. Replace the control compartment access door and gasket,

and secure with the twelve (12) previously removed screws

(Figure 7).

4. Carefully slide the burner assembly venturi onto the oriﬁ ce.

While placing the burner assembly onto the brackets,

reinstall the air shutter adjustment lever (Figure 5). Secure

the burner assembly with the two (2) previously removed

screws.

Install rear ﬂ oor section (from required ﬂ oor kit)

1. Place lower back edge of rear ﬂ oor section on rear ledge of

ﬁ replace, behind the tabs (Figure 22).

2. Align outermost front hole on either side of rear ﬂ oor

section with hole in center lower tab in each side panel. Pull

rear ﬂ oor section forward until it butts against the burner,

and secure using ﬁ ve (5) #10-16 x 3/8 hex-head sheet

metal screws provided with the ﬂ oor kit.

f i r e - p a r t s . c o m

Side Panel

(Center Lower Tab)

Figure 22 - Installing the rear ﬂ oor section

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

Rear

Floor

Section

Tab

Rear

Ledge

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Install front ﬂ oor section (from required ﬂ oor kit)

1. Engage the lower front lip of the front ﬂ oor section under

the locking clips attached to the ﬁ replace front ledge, and

then slide it back (Figure 23).

2. Align the notches in the back edge of the front ﬂ oor section over

the holes in the rear ﬂ oor section. Push the front ﬂ oor section

backward until it butts against the burner, and screw the front

ﬂ oor section as shown in Figure 23.

Front

Floor

Section

Front

Ledge

Lip

Locking Clip

Figure 23 - Installing the front ﬂ oor section

Install media (from optional media kit)

WARNING

• Handle media only when cool. Turn OFF all electricity

to the appliance before installing media. Media gets

very HOT during ﬁ replace use and will remain hot up

to ONE HOUR after the gas supply is turned off.

• Any attempt to use media not speciﬁ ed for your ﬁ replace

conﬁ guration will result in incomplete combustion,

sooting, and poor ﬂ ame quality, and will void the

warranty.

• Do NOT mound up media, especially on the burner.

• If using multiple colors of media, NEVER use more

than ﬁ ve (5) pounds total (approximately) at one time.

• Do NOT allow media to get into the pilot hole.

1. If installing a ﬂ oor kit that requires media, place an even

layer of media in the recessed area around the burner (see

bold outlined area in Figure 24; also refer to Figure 1).

Figure 24 - Placement of media

Notch

Rear

Floor

Section