Bosch 800 Series Panduan Instalasi - Halaman 13

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Mesin pencuci piring Bosch 800 Series. Bosch 800 Series 48 halaman. Built-in wall ovens
Juga untuk Bosch 800 Series: Panduan Petunjuk Instalasi (24 halaman), Panduan Instalasi (40 halaman), Panduan Penggunaan dan Perawatan (12 halaman), Panduan Instalasi (23 halaman), Panduan Instalasi (28 halaman), Panduan Instalasi (32 halaman), Buku Petunjuk (32 halaman), Panduan Instalasi (32 halaman), Panduan Memulai Cepat dan Keselamatan (7 halaman), Panduan Penggunaan dan Perawatan (40 halaman), Panduan Instalasi (40 halaman), Panduan Instalasi (32 halaman), Panduan Petunjuk Instalasi (40 halaman), Panduan Penggunaan dan Perawatan (33 halaman), Panduan Penggunaan dan Perawatan (49 halaman), Panduan Memulai Cepat (7 halaman), Panduan Memulai Cepat dan Keselamatan (13 halaman), Panduan Instalasi (32 halaman), Panduan Servis (36 halaman), Panduan Petunjuk Instalasi (29 halaman), Panduan Penggunaan dan Perawatan (24 halaman), Panduan Penggunaan dan Perawatan (40 halaman), Panduan Petunjuk Instalasi (28 halaman)

Halaman Cetak
Bosch 800 Series Panduan Instalasi
Screw the adjustable feet into the mounting holes on
4.
the underside of the appliance.
Note: If the appliance needs to be moved again,
screw the adjustable feet in fully.
Carefully move the appliance back onto its feets.
5.
Turn the adjustable feet to align the appliance.
6.
Note: Measure the installation height of the cabinetry
and adjust appliance height accordingly prior to
placing appliance in cabinetry.

Connect Gas Supply

The appliance is shipped from the factory for use with
natural gas at a pressure of 5" water column. When
checking for proper operation of the regulator, the inlet
pressure must be at least 1" greater than the operating
(manifold) pressure above. When used with natural gas,
the pressure supplied to the regulator must be between
6" and 10,5" water column.
To convert the appliance to propane gas see
"Conversion to propane gas (LPG)". A qualified
technician or installer must do the conversion.
Use a flexible gas pipe with a length of at least 5 ft
(1.5 m).
The gas inlet to the unit is located at the right rear of the
appliance.
Install the pressure regulator (supplied with unit) to gas
inlet. Postion the gasket (supplied with unit) in between
the inlet and the regulator. Position the regulator to have
it cap D (~ Page 19) easily accessible. Turn the nut on
gas inlet to hand tighten plus 1/3 turn.
Install the gas pipe to the regulator using Teflon tape or
pipe-joint compound (resistant to propane gas and
natural gas). Turn to hand tighten plus 1/3 turn. Do not
exceed 1 turn for alignment, to prevent possible damage
to the gas pressure regulator.
Check inlet fittings and regulator for leaks.
* Attached to the appliance.
WARNING
9
Do not attempt any adjustment of the pressure
regulator, except when converting to propane.
Adjustments could lead to leaks or cause incorrect
gas pressure to the appliance.
Side and Back View Gas Cooker Installation
Gas Location
Gas connection
A
Electrical connection
B
Connect the gas supply line to the unit pressure
regulator using a 1/2" flex gas line connector between
manual shut-off valve and pressure regulator. A metal
flex line or fixed metal pipe shall be used to connect gas
to the appliance. If a metal gas line cannot be used,
consult your local certified electrician or local electric
codes for proper grounding.
13