Carolina UltaSpot Buku Petunjuk

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Lampu Banjir Carolina UltaSpot. Carolina UltaSpot 4 halaman.

READ THOROUGHLY BEFORE INSTALLING

OVERVIEW

This product was designed from the ground up to be the most efficient and reliable flood lighting product on the market. Please read and understand all installation

instruction prior to installing. Should you have any questions, do not hesitate to contact your local agent or Carolina High Mast for clarification.

UNPACKING

The UltaSpot ships preassembled in one shipping package. The package is

designed to minimize risk of damage to the luminaire during shipping and

handling. It is recommended that the UltaSpot is not removed from the

packaging unless it is to be immediately mounted on the support structure.

Each package contains an exterior label that identifies the wattage and

lighting distribution. In preaiming lighting systems, each package also

uniquely identifies the appropriate tower and cross arm location.

WARNING: Removing the fixture from the packaging and setting on the

ground could damage the glass or exterior finish. Care should be taken to

protect the unit if it is to be removed from the packaging and not

immediately bolted to the support structure.

INSTALLATION

MOUNTING

The flood light is provided with a heavy duty mounting trunion. The

mounting trunion has clearance for a ¾" main attachment bolt. Raise

the luminaire into position and attached the main ¾" trunion bolt.

Snug tight the main bolt to hold the luminaire in place. The luminaire

shall be adjusted to the proper left-right aiming angle by rotating the

luminaire on the main trunion bolt. Once the proper left-right aiming

angle has been achieved, tighten the main trunion bolt to 80-90 ft*lb

of torque. NOTE: Refer to aiming instructions for additional details

on proper aiming procedure.

WIRING

Make all connections in accordance with the National Electric Code

and any applicable local code requirements. Verify that the supplied

voltage (as marked on the luminaire packaging) matches the supply

voltage to the lighting unit. NOTE: If the luminaire is supplied with

an optional Brad Harrison style connector, skip this step.

Remove the rear ballast cover by removing the (4) #10

screws

The luminaire includes a weather tight cord grip in the

lower portion of the ballast housing. It is recommended

that the luminaire be wired with a minimum 16/3

SEOOW (90C+ rating). The cord grip may need to be

loosened to ensure the cable easily slides into the ballast

housing.

The ballast is factory prewired for the desired site

voltage. Three wires include an electrical butt-splice.

The leads are covered in a high temperature protective

fiberglass cover. Push back the coating to access the

butt splice as needed. Using a cable crimp tool, match

the color code of the incoming 16/3 to the supplied

wires (Black/White/Green). WARNING: In a L-N-G

system, ensure the system neutral is connected to the

The included installation instructions are not to be considered to cover all details. General best practice and safety precautions should be taken when working with

electrical equipment such as this. Should there be any uncertainty about the guidelines contained herein, Carolina High Mast or an Carolina High Mast

representative should be contacted immediately for further guidance.

Document Revision 07/18/14

UltaSpot FLOOD LIGHT

incoming white wire only. G is exclusively reserved for

electrical ground and B is always hot (Line).

Once the incoming power is connected to the butt splice

connectors, push the fiber glass wire covering over the

butt splice, and push over incoming cable to within 1" of

cord grip. NOTE: The fiberglass covering protects the

wires in case of contact with the ballast and full covering

of the incoming wire is critical.

Once the electrical connections are made, ensure the

supplied cord grip is properly tightened on power cable.

Reattached the ballast housing cover by tightening the

(4) #10 screws.

LAMPING

Open the optical housing by manually releasing each of the glass

clamp draw latches. This process should be accomplished without

the use of tools! Install the lamp that was supplied with the

luminaire by Carolina High Mast. The lamp shall be hand tightened

to approximately 35 in*lb. Care should be taken to ensure clean

hands and/or gloves are used when handling the lamp and optical

surface. NOTE: Carolina High Mast has designed the UltaSpot

around a specific set of high performance, energy efficient lamps.

Lamps shall not be substituted without written authorization from

CHM. Close the glass door and reattach the glass support latches.

Ensure the wire from the glass latch has properly seated in the strike

plate and that all latches are properly engaged. (NOTE: If the glass is

not properly sealed, dirt and contaminants will seep into the optical

reducing overall luminaire efficiency)

AIMING PREPARATION

Prior to aiming of the flood lighting fixtures, it is critical to ensure the

proper distributions are located in the appropriate location on the support

structure. The ballast housing will include a large label on the field side of

the housing indicating the lighting distribution (e.g. N, M or W).

Distributions should be matched to the supplied aiming array illustrating

the fixture array, aiming angles and specific distribution.

DEGREE AIMING

The UltaSpot is provided with a horizontal and vertical aiming indicator.

These aiming indicators can be used for general aiming indication. NOTE: If

precision aiming is required, the target aiming process should be followed.

Contact CHM for detailed target aiming instructions.

In the pre-aimed configuration, both the horizontal and vertical aiming

indicators with be marked with the appropriate aiming settings. Adjust the

luminaire until the aiming mark aligns with the aiming bolt. IF the fixture is

not pre-aimed from the factory, follow the aiming steps below.

INSTRUCTIONS