AquaPRO 03AP546 Petunjuk Manual - Halaman 3

Jelajahi secara online atau unduh pdf Petunjuk Manual untuk Sistem Penyaringan Air AquaPRO 03AP546. AquaPRO 03AP546 8 halaman. Pressure filter uv clarifier
Juga untuk AquaPRO 03AP546: Petunjuk Manual (16 halaman)

Halaman Cetak

1. Technical Specifications

PRODUCT SPECIFIC SAFEGUARDS

• Do not operate the UVC Lamp without water at any

time, permanent damage may occur.

• The pump is designed to be used in a Fresh water

Garden pond. It is not to be used in any other manner

or purpose. The pump should only be used in clean

water.

• AQUAPRO Filtration & Waterfall Pumps are

cooled by water flowing through the inside of the

motor body. If the pump flow becomes restricted it

will overheat and could cause permanent damage.

Large tubing size is strongly recommended to deliver

adequate water flow to cool the pump. The pump

needs to be cleaned regularly to prevent the pump

INSTALLATION

IDENTIFY A SUITABLE LOCATION FOR YOUR NEW PRESSURE FILTER.

• Do not submerge this product in water. The pressure

filter should be used inline, between a pump and

a water feature or waterfall. The filter can also be

partially buried to help disguise it in your garden.

• Place the filter on a firm and level base, e.g. on a slab.

Please make sure that there is unhindered access to

the lid in order to be able to carry out maintenance on

the filter, e.g. cleaning the filter sponges.

• It is good practise to design the plumbing beforehand.

Ensure the pipes are laid out such that the clean

filtered water return is to the opposite end of your

pond to where the pump suction is located. This aids

circulation and is to avoid stagnant spots.

• Select the hose tail, locking nut, and flat rubber

washer. Assemble as per diagram. Insert into the end

of tubing.

• Connect anti-kink hose or poly tubing from your

pump outlet to the inlet of the filter.

• If your filter has a three step hose tail to suit smaller

tubing, then be sure to cut off the hose tails that are

smaller than the hose size you are using. For example,

If using 40mm hose, cut off the 25 & 32mm sections.

Please use the largest size tubing possible. We

recommend using AQUAPRO hose clamps for a leak

free connection.

[email protected]

AQUAPRO AP5000UV Instructions.indd 3

AP5000UV PRESSURE FILTER

WWW.AQUAPROONLINE.COM.AU

WEB

I N S T R U C T I O N S

becoming blocked, thus causing the pump to overheat

and burn out. This is not a warrantable event. It is

strongly recommended not to select a pump that is

too small for the job required. The flow rate through

the pump needs to be strong enough so that a half of

the rated max flow is kept running at all times.

• Connect the tubing from the outlet of the filter back

into your pond at the opposite end to where you

are pumping from. It's possible to have the outlet of

the filter running into a waterfall. You only need to

connect tubing to the back-flush outlet if you require

the dirty water from the backwash to be diverted to a

specific location.

• If the flow from your pump is greater than the

recommended max flow, you must reduce the flow,

or bypass some of the water with a Y junction piece

between the pump and the filter. The flow of water

through branch of the Y junction can be varied by use

of an optional valve. The pressure must not exceed

3M head pressure.

• The filter must be operational 24 hours every day for

it to function effectively.

• Turn your pump on and then plug in the UV-C unit on

the filter. The UV-C unit should not be turned on if

there is no water flowing post the UV-C unit.

• It is recommended to boost the biological function of

your filter with AQUAPRO Bacteria. This will greatly

increase the efficiency of the unit.

• Now sit back, relax and enjoy a clean and healthy

pond.

13/5/2022 8:23 am