AquaPRO 03AP546 Інструкція з експлуатації - Сторінка 3
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Системи фільтрації води AquaPRO 03AP546. AquaPRO 03AP546 8 сторінок. Pressure filter uv clarifier
Також для AquaPRO 03AP546: Інструкція з експлуатації (16 сторінок)
Друкувати сторінку
PRODUCT SPECIFIC SAFEGUARDS
• Do not operate the UVC Lamp without water at any
time, permanent damage may occur.
• The pump is designed to be used in a Fresh water
Garden pond. It is not to be used in any other manner
or purpose. The pump should only be used in clean
water.
• AQUAPRO Filtration & Waterfall Pumps are
cooled by water flowing through the inside of the
motor body. If the pump flow becomes restricted it
will overheat and could cause permanent damage.
Large tubing size is strongly recommended to deliver
adequate water flow to cool the pump. The pump
needs to be cleaned regularly to prevent the pump
INSTALLATION
IDENTIFY A SUITABLE LOCATION FOR YOUR NEW PRESSURE FILTER.
• Do not submerge this product in water. The pressure
filter should be used inline, between a pump and
a water feature or waterfall. The filter can also be
partially buried to help disguise it in your garden.
• Place the filter on a firm and level base, e.g. on a slab.
Please make sure that there is unhindered access to
the lid in order to be able to carry out maintenance on
the filter, e.g. cleaning the filter sponges.
• It is good practise to design the plumbing beforehand.
Ensure the pipes are laid out such that the clean
filtered water return is to the opposite end of your
pond to where the pump suction is located. This aids
circulation and is to avoid stagnant spots.
• Select the hose tail, locking nut, and flat rubber
washer. Assemble as per diagram. Insert into the end
of tubing.
• Connect anti-kink hose or poly tubing from your
pump outlet to the inlet of the filter.
• If your filter has a three step hose tail to suit smaller
tubing, then be sure to cut off the hose tails that are
smaller than the hose size you are using. For example,
If using 40mm hose, cut off the 25 & 32mm sections.
Please use the largest size tubing possible. We
recommend using AQUAPRO hose clamps for a leak
free connection.
AQUAPRO AP5000UV Instructions.indd 3
AQUAPRO AP5000UV Instructions.indd 3
AP5000UV PRESSURE FILTER
WWW.AQUAPROONLINE.COM.AU
WEB
I N S T R U C T I O N S
becoming blocked, thus causing the pump to overheat
and burn out. This is not a warrantable event. It is
strongly recommended not to select a pump that is
too small for the job required. The flow rate through
the pump needs to be strong enough so that a half of
the rated max flow is kept running at all times.
• Connect the tubing from the outlet of the filter back
into your pond at the opposite end to where you
are pumping from. It's possible to have the outlet of
the filter running into a waterfall. You only need to
connect tubing to the back-flush outlet if you require
the dirty water from the backwash to be diverted to a
specific location.
• If the flow from your pump is greater than the
recommended max flow, you must reduce the flow,
or bypass some of the water with a Y junction piece
between the pump and the filter. The flow of water
through branch of the Y junction can be varied by use
of an optional valve. The pressure must not exceed
3M head pressure.
• The filter must be operational 24 hours every day for
it to function effectively.
• Turn your pump on and then plug in the UV-C unit on
the filter. The UV-C unit should not be turned on if
there is no water flowing post the UV-C unit.
• It is recommended to boost the biological function of
your filter with AQUAPRO Bacteria. This will greatly
increase the efficiency of the unit.
• Now sit back, relax and enjoy a clean and healthy
pond.
13/5/2022 8:23 am
13/5/2022 8:23 am