FIAMA F7- Panduan Pengguna dan Pemeliharaan - Halaman 5
Jelajahi secara online atau unduh pdf Panduan Pengguna dan Pemeliharaan untuk Monitor FIAMA F7-. FIAMA F7- 12 halaman. Display for magnetic band with battery power supply
Halaman Cetak
Display for magnetic band
pressing 2 times
ENTER
radius of cutter 0), which is then confirmed by pressing
Now
will appear which is the nominal value for tool 1 (for example the radius of cutter 1): set
the correct value and confirm with
Finally
will appear which is the nominal value for tool 2 (for example the radius of cutter 2):
set the correct value and confirm with
In practice
,
which are used.
As a special case, if
origin 2 respectively.
/
function: Enables passing from an absolute to relative value; after pressing
ABS
REL
displayed value is temporarily set to zero to measure a relative motion of the transducer. On the
display the
icon indicates that the current display is relative to the reference point that has just
REL
been created. Pressing again
appear.
mm/inch conversion: Pressing
back. When in inch mode, the
decimal place. When the parameter
Offset: This parameter is added to or subtracted from the displayed value to correct it in case, for
example, of a tool change or to compensate tool wear. After setting a positive offset value, the
displayed value will be the measured value plus the offset value. After setting a negative offset
value, the displayed value will be the measured value minus the offset value.
Fast Offset: After pressing
it is possible to set directly the value to be displayed (use buttons
/
). This function is useful if it is necessary to correct often the displayed value.
ENTER
RESET
Count direction
Set out the count direction of the display, range allowed 0 or 1.
Adjustment of displayed value
After the installation of instrument on the machine and setting of all parameters, in order to visualize
on the display the correct value it is necessary to carry out the reset or preset.
Position the shaft in a point in which the correct measure that has to be visualized is known exactly
(for example the stroke end point) or measure the position in that point of the shaft. Program
parameter
with value 3 in the first digit on the right and exit programming.
Now press
/
ENTER
RESET
value to display, then confirm with
If the required value is zero, instead of the preset function it is possible to use the reset function by
setting 1 in the first digit on the right in the
the displayed value to zero.
Now that the instrument is adjusted, it is necessary to insert the desired
accidental reset/preset of the displayed value.
Battery replacement
The instrument is supplied with a ½AA 3,6V lithium battery, which assures a typical functioning of
approximately 4 years.
When the battery runs down, an icon appears on the display.
To enter into the battery-holder it is necessary to remove the front cover by carefully inserting a flat
screwdriver on the sides. After taking off the cover, pull the battery out and substitute it with a new
one, paying attention to the polarity: the positive pole must face the side of the
button. The instrument is protected against inversion of polarity and wrong insertion, and in this
case will not switch on.
Data: 13/01/16
/
it is possible to set the nominal value for tool 0 (for example the
RESET
/
ENTER
RESET
ENTER
, and
are the nominal values associated to the three different tools
is set to zero,
causes the absolute value to be displayed and the
converts the measurement from millimeters to inches and
icon will appear and the displayed value will have an additional
INCH
=4 the mm/inch conversion is not available.
/
,
ENTER
RESET
and
will appear, press again 2 times
/
ENTER
RESET
/
ENTER
RESET
.
/
.
RESET
and
are the values to display in origin 1 and in
appears and by pressing two times
. The display will now show the desired value.
parameter so that pressing
F7_ing.doc
.
ABS
ENTER
and confirm with
/
and set the correct
ENTER
RESET
/
ENTER
RESET
parameter to avoid
ENTER
F7
, the
icon will
/
RESET
will bring
/
RESET
pag 5/12