ARGSeguridad ZDAS-300 Panduan Pengguna - Halaman 11

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Sistem Keamanan ARGSeguridad ZDAS-300. ARGSeguridad ZDAS-300 16 halaman. Luxury voiced lcd alarm system

Halaman Cetak

4 USER INFORMATION:

4.1 Methods of Arming and Disarming

Arming: Arming is used to arm the whole Alarm system. All detectors in the zones within

the protected area must be closed(not in alarm)in order for you to arm the system successfully.

Part Arming: Part Arming is used to partially Arm your System by arming the selected

zones in the protected area,which permits persons to remain in the premises while the system

is Part Armed.

Disarming:Disarms the system and deactivates any alarms in progress and disarms all the

zones other than the 24 hour Zones.

4.1.1. Arming and Disarming through the Keypad on the panel

How To Arm: Pressing the ARM key on the keypad to arm the system.

How To Part Arm: Pressing the ARM Key on the Keypad for 2 seconds to Part Arm the

system.

How To Disarm: Press the DISARM key on the keypad then using the Keypad again enter

the pre-programmed 6 digit PIN code to complete the disarming operating.

4.1.2. Arming and Disarming through the Key Fob Remote Device

How To Arm: Press the Arm key on the Key Fob to Arm the system.

How To Part Arm: Pressing the Part Arm key on the key Fob to Part Arm the system.

How To Disarm: Press the DISARM key on the key Fob to Dis-Arm the system.

Note: The armed LED flashes to show that the delay timer is being activated for those

zones with delayed time. The zones without a delayed timer is armed. When the armed LED

light, it shows Arming has completed. All the exterior Zones Arm immediately when part

armed, the delay timer will not work under such circumstances.

3.4 Installing wired detector and its zone setting:

Various wired detector could be connected to the panel via the N.C terminal. Seven wired

connection in all, and the terminals for connection are 1\2\3\4 \5\6\7, GND is the common

terminal.

Zone setting:

After connecting well the wired detector to the panel,press the PROG key

on the keypad, a series of ----- appear on the LCD. Enter the PIN code or press the Disarm key

on a registered key fob and the word 'Sensor' will appear on the LCD.Trigger the detector you

wish to register, the panel will receive the detectors code and the word 'CODE' will appear on

the LCD.Pressing a numeric key 1 to 8 on the keypad will select the zone you wish to allocate

the detector. e.g. Pressing No 3 on the keypad will allocate the detector to Zone 3. The control

panel will then automatically allocate the detector with the next available detector number in

that Zone. So, if there are no detectors allocated in Zone 3 the control panel will allocate it as

detector No 1 and the next detector to be registered in Zone 3 will be allocated detector No 2

etc. To complete and save the information press PROG key.

( Also you could first fix two wires to terminal 1.2.3.4.5.6 or 7 and GND, then connect

them together. Disconnect them when triggered. It is ok then to replace with a wired detector

after registration.)

3.5 Checking Registration

Checking key fob and sensor registration:press the # key on the keypad,the LCD displays

word TEST, Activate a detector, a bleep noise will be heard confirming the control panel has

received the signal from the detector and the LCD will display the Detector registration No

and its Zone allocation e.g. Activate Detector No 2 in Zone 3 the LCD will

LOG

Figure 9

TEST