ALTONOVUS OR-01 Panduan Memulai Cepat

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Alat Ukur ALTONOVUS OR-01. ALTONOVUS OR-01 2 halaman. Low compliance voltage ohmmeter

Halaman Cetak

DEVICE

USE AND CARE

Do Not immerse in,

or expose to liquid.

IP54 rated.

Do Not drop, expose to

shock, or place heavy

objects on unit.

Do Not apply pressure

to display.

Only use a clean,

dry cloth to clean

unit.

BEFORE USE

INSERT 2 x AA BATTERIES

2 x AA alkaline batteries will give in excess of 150

hours of continuous operation. Treat all batteries in

accordance with the manufacturer's instructions.

1. Remove battery compartment cover (H) applying

gentle pressure to finger pad.

2. Ensure clean contacts on batteries.

3. Insert new batteries, observing polarity

instructions in battery compartment.

4. Replace battery compartment cover.

If desired, remove the protective film from the front of

the ΩhmRanger-LCV. Peel carefully from below the

Positive

ΩhmRanger-LCV will still function normally if the film

is left in place.

SCREEN GUIDE

- The Resistance reading, displayed in MΩ, KΩ and Ω. In the example

above, 2.1MΩ.

- A small, oscillating Range Bar shows which range is currently in use.

An upper, longer Range Coverage Bar shows any movement across the

ranges during the reading (in this case, none). The box surrounding

shows the operating range.

- The Voltage being applied by ΩhmRanger-LCV at the

terminal, in this case 206.7mV, to measure the resistance.

- The active Range and the measured Current.

- The Signal to Noise Ratio (SNR). The SNR indicates how much noise,

variation, and AC components are in the signal, followed by Maximum and

Minimum Current samples during the reading. Higher resistances (lower

currents) are more susceptible to noise.

USE THIS QUICK START GUIDE IN CONJUNCTION WITH THE FULL INSTRUCTION MANUAL. DOWNLOAD AT:

Avoid extremes of

temperature. Max

accuracy in 20-25

degree Celsius range.

No User-serviceable

components. Do Not

open unit, as it voids

warranty and

calibration.

Minimum stimulus

applied is 206mV. Do

not expose unit to

currents over 800mA.

and Negative terminals.

Positive

MODEL: OR-01: LOW COMPLIANCE VOLTAGE OHMMETER.

QUICK START GUIDE (Rev 1.0 dated 10 MAR 22)

ALTONOVUS LTD. 37 OAST HOUSE CRESCENT, FARNHAM, SURREY,

GETTING STARTED - TAKE A READING

WARNING. Use

ΩhmRanger-LCV

with cables less

than 3 metres.

STEP 2: CONNECT LEADS

Connect the Resistance to be

measured between the

Positive

(RED) and Negative (BLACK)

terminals of the ΩhmRanger-LCV.

Leads (not supplied) should be

industry standard, uninsulated, 4mm

banana plug. Leads of shorter

length will help minimise any noise.

STEP 4: POWER OFF

After measurements

are taken, press the

POWER button

again to return

ΩhmRanger-LCV

to Standby mode.

A -

Positive

Terminal

B - Negative Terminal

C - Display Screen

D - On / Off Button

E - Menu Navigation

F - Select Button

G - Isolated USB Interface

H - Battery Compartment

STEP 1: POWER ON

After inserting batteries

as shown, press the

POWER button to start

ΩhmRanger-LCV.

STEP 3: TAKE MEASUREMENTS

Sampling at a high rate to

eliminate mains noise, Ωhm-

Ranger-LCV takes about 2.5

readings per second. It displays

the current in MΩ, KΩ and Ω. In

this example, 2.1MΩ.

A Range Bar below the digits

shows which ranges are, and have

been in use. The Range Bar

oscillates after each reading to

show how quickly readings are

occurring and to show that the

device is functioning correctly.