ADEMCO 5817CB Manuale di installazione e configurazione - Pagina 2

Sfoglia online o scarica il pdf Manuale di installazione e configurazione per Trasmettitore ADEMCO 5817CB. ADEMCO 5817CB 2. Wireless commercial / household transmitter
Anche per ADEMCO 5817CB: Istruzioni per l'installazione (4 pagine), Manuale di avvio rapido (2 pagine), Manuale di installazione e configurazione (2 pagine), Istruzioni per l'installazione (2 pagine)

Stampa la pagina

ADEMCO 5817CB Manuale di installazione e configurazione

Attach the case back to the mounting plate by sliding the keyhole slots in the case back down onto

the mounting plate's holding posts. The locking tab will click as the case back locks in place. To

disengage the unit from an installed mounting plate, insert a small screwdriver into the

mounting plate release hole, push down to retract the locking tab, and push upward on the unit to

disengage from posts. If not using the mounting plate, it is necessary to remove the PC board

from the case back. Slide a small flat bladed screwdriver between the case back and PC board near

the board hold-down clip and carefully pry the board out.

In the area that was previously marked for the location of the mounting plate, (step 4), install the

hold-down tab with a 5/8" flat head dry-wall screw. The tab must be aligned with the corresponding

slot in the case back as shown in Figure 2. The tab as well as the case back must be anchored to a

wall stud or other solid wood material.

To reinstall the PC board into the case back, position the board onto the two retaining studs on one

side of the case back and snap the board into place. The hold-down tab must mate with the

corresponding cutout in the case back after case back is installed.

Reverse the procedure of the first three steps to complete reassembly of the unit.

10. Set the DIP switch (after the control panel has enrolled the transmitter's input IDs) for the desired

primary loop characteristics, as described in the table below.

PRIMARY LOOP OPTIONS TABLE

SWITCH

SETTING

REPEATING TRANSMISSION

(every 4 sec.)

UPON PRIMARY LOOP FAULT

Use for high priority

alarm, such as fire.

OFF

SINGLE TRANSMISSION

PER PRIMARY LOOP CHANGE-OF-

STATE

Notes:

a. In order for the control panel to enroll the transmitter, the DIP switches must be

set to OFF – ON – ON – OFF (see Figure 3).

b. The Auxiliary loops are not affected by the DIP switch settings.

UL REQUIREMENT

If using one of the panel revisions shown in the following table, and programming the 5817CB as an

Entry/Exit zone, you must enroll the tamper loop (loop 4) as a separate zone, programmed for 24-

hour response (e.g., Zone type 5  Trouble-by-day/Alarm-by-night).

Model #

Rev.

EPROM P/N

FA1600C

(WAVIS150FA-18)

Vista-32FB

(WAVIS32FB-13)

Vista-128FB

(WAVIS128FB-14)

Vista-128B

(WAVIS128B-13)

For UL Commercial Burglary installations, this transmitter must be used in conjunction with the

5881ENHC RF Receiver.

WIRING CONNECTIONS

Connect the loop wiring to the unit's terminals before installing the battery (see Figure 3).

Notes:

Primary loop 1 is a supervised loop and must have an end-of-line (EOL) resistor (470K

ohms, supplied) placed across the last sensor. Additionally, for Primary loop 1, a contact

device may not be installed more than 20 feet from the transmitter.

If loop 2 is not going to be used, the magnet is not necessary.

If loop 3 is not going to be used, no connection is needed across its terminals. For UL

household burglary and fire installations, the loop 3 contact device (if used) may not be

more than 3 feet from the transmitter.

BATTERY INSTALLATION/REPLACEMENT

1. Remove the transmitter's cover as described in Mounting Step 1.

2. Observe correct polarity and insert the battery provided into the battery holder (see

Figure 3). Take care not to bend the antenna.

DIP SWITCH POSITION

SWITCH

SWITCH MUST

MUST

ALWAYS BE

IN THE

POSITION

- 2 -

Note:

Replace battery only with: Duracell DL123A, Panasonic CR123A or Ademco 466.

Risk of fire, explosion, and burns. Do not recharge, disassemble, heat above 212°F

(100°C), or incinerate. Dispose of used batteries promptly. Keep away from children.

CAUTION:

3. To replace the cover, engage the hooks along the top edge and snap shut.

SPECIFICATIONS

Dimensions:

1-9/16"W x 3-1/2"H x 1-3/16"D (40mm x 89mm x 30mm)

Battery:

3V Lithium (see BATTERY INSTALLATION/REPLACEMENT).

Signal Level:

To determine ambient noise level and signal strength, refer to compatible receiver

Installation and Setup Guide.

UL Listings:

Commercial Fire....... ......... UL864

Household Fire....... ........... UL985

Household Burg .................. UL1023

Commercial Burg............... UL365, UL609, UL1076, UL1610

TESTING

Regular maintenance and inspection (at least annually) by the installer are vital to continuous

satisfactory operation of any alarm system. The installer should instruct the user to test the system

frequently (at least weekly) to insure the system's operation at all times, as well as offer a regular

maintenance program to the user.

ALWAYS BE

limitations of the entire alarm system. For testing procedures, refer to the User Guide or Installation

IN THE

and Setup Guide for the system control panel.

OFF

FOR LIMITATIONS OF THE ENTIRE ALARM SYSTEM, REFER TO THE CONTROL PANEL'S

POSITION

INSTALLATION AND SETUP GUIDE FOR THE RECEIVER/CONTROL WITH WHICH THIS DEVICE IS

USED.

MOUNTING

PLATE

HOLE

TAMPER SWITCH

HOLD DOWN

CONCEALED

WIRING

ENTRY

HOLE

Figure 1. Mounting Plate

NOTE:

For UL commercial and

household fire installations, only

one initiating device may be

connected to this transmitter. For

UL commercial burglary

installations, multiple initiating

devices may be used as long as

the devices all serve the same

function, such as door/window

contacts, motion or glassbreak

detectors. All initiating devices

must be located within the same

room.

No more than one wire per

terminal may be connected.

Use only 14-22AWG wire.

Risk of fire, explosion, and burns. Do not recharge, disassemble, heat

above 212°F (100°C), or incinerate. Dispose of used batteries promptly.

Keep away from children.

Household Burg........UL1023

The user should also be acquainted with proper operation and

HOLD-DOWN

TAB

TAMPER SWITCH

HOLD-DOWN TAB

CASE

HOLDING

POSTS

INSTALL

IN LINE WITH

MOUNTING

CUT-OUT

PLATE HOLE

IN CASE BACK

CONCEALED

WIRING

LOCKING

TAB

ENTRY HOLE

5817CB-001-V1

THE DIP SWITCHES MUST BE

SET AS SHOWN DURING

ENROLLMENT BY THE CONTROL

WHITE AREA

INDICATES

SWITCH HANDLE

OFF

DIP SWITCH FOR PRIMARY LOOP OPTIONS

(SEE SETTINGS TABLE)

SHOWN SET FOR: 1. SINGLE TRANSMISSION

NOTE: SW2 MUST BE ON

SW3 MUST BE ON

SW4 MUST BE OFF

CONCEALED

WIRING ACCESS

Figure 3. 5817CB Transmitter, Top Cover Removed

- 3 -

CASE BACK

MOUNTING

HOLES (2)

5817CB-001-V0

Figure 2. Case Back

COVER

HOLDING

ANTENNA

SLOTS (2)

ALIGN MAGNET

WITH MARKS ON

CASE (2 PLACES)

LOOP 2

REED SWITCH

(AUX)

DIP

SWITCH

BATTERY

MAGNET

(OBTAIN

SEPARATELY)

–

1/2"

COVER

MAX.

TAMPER

SWITCH

LOOP 3

PRIMARY

TERMINALS

LOOP 1

(AUX)

TERMINALS

MOUNTING

CLASS B

SLOT FOR

PLATE

CIRCUIT

COVER

RELEASE

PRY-OFF

POINT

N.O.

N.C.

CONTACT

EOLR

470K ohms

DEVICE

5817CB-002-V2