- ページ 4

投影スクリーン Draper NocturneのPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。Draper Nocturne 4 ページ。 Draper nocturne exterior projection screen

ページを印刷する

Nocturne Exterior Projection Screen by Draper

RTS Motor/Remote Programming Instructions

If you receive a Nocturne with an optional RTS motor from Draper,

Inc., the motor has no programming on it, so it must be learned and

programmed to work on the transmitter that you have. The limits must

also be set. Here are the initial programming instructions.

➀ Connect power to motor. Select the transmitter/channel to which

you plan to learn the motor. Press and hold the UP and DOWN

buttons at the same time until the motor jogs, then release.

➁ Check the motor run direction by press either the UP or DOWN

buttons. This is important because if you do step 3 without doing

this step, then you will need to reset the motor. If you need to

reverse the motor direction, then press the STOP button (middle

button which might be labeled MY) for 5 seconds until the motor

jogs. Check the direction again to make sure that it works.

➂ Move the motor to its upper limit position. Press the STOP and

DOWN buttons at the same time until the motor starts to move

down, then release. You will stop the motor at its lower limit. You

can use the UP and DOWN buttons to adjust the motor to the

correct lower limit position if need be.

➃ Once the motor is at its lower limit position, then press the UP and

STOP buttons at the same time until the motor starts to move up,

then release. The motor should move to the upper limit position in

step 3 and stop.

➄ Once the motor has stopped at its upper limit position, then press

and hold the STOP button for 5 seconds until the motor jogs.

➅ Now, you must put the motor into USER mode. Find the program-

ming button which is a small button on the back or side of the trans-

mitter and press it until the motor jogs. Once you have done this,

then the motor will operate in normal fashion.

➆ Disconnect power to this motor and move to the next in your

installation and start with step 1. Reconnect motor to power when

all motors are programmed.

Reset Motor Instructions

If the motor is not working or responding correctly and you want to

reprogram it from the beginning and clear all previous programming,

then follow these steps.

➀ Disconnect the motor from power for 2-5 seconds, reconnect to

power for 10-13 seconds, disconnect from power for 2-5 seconds,

and reconnect to power. The motor should move down a little after

you reconnect to power the last time.

➁ You will then need to ﬁ nd the programming button which is a small

button on the back or side of the transmitter. You will need to de-

press the button for 10-15 seconds. The motor should jog up and

down once then pause and jog a second time during this time

period. Once the motor has completed its second jog, then you can

start at step 1 of initial programming as the motor is clear.

Add/Delete a Channel/Transmitter

Add:

➀ Select the channel/transmitter that is currently operating the motor,

then press the programming button until the motor jogs.

➁ Select the new channel/transmitter that you want to add to the

motor, then press the programming button until the motor jogs.

Channel se-

lector button

on Multi-

Channel

Transmitter

➂ The motor should now work on both the old and new channel/

transmitter.

Delete:

➀ Select the channel/transmitter that is currently operating the motor

and you want to keep, then press and hold the programming button

until the motor jogs.

➁ Select the channel/transmitter that you want to remove, then press

and hold the programming button until the motor jogs.

➂ The motor should now only work on the channel/transmitter from

step 1.

Adjust Limits in User Mode

If your initial limits have changed or you want to ﬁ ne tune a motor,

you do not need to reset the motor and re-program it. You can just

change the limits with these steps.

➀ Move the motor to the limit (upper or lower) that you want to

change.

➁ Press and hold the UP and DOWN buttons until the motor jogs.

➂ Move the motor to its new limit location.

➃ Press and hold the STOP button until the shade jogs.

www.draperinc.com

(765) 987-7999

Page 4 of 4