- ページ 6

歯科医療機器 3Shape TRIOS S1P-2のPDF セットアップマニュアルをオンラインで閲覧またはダウンロードできます。3Shape TRIOS S1P-2 13 ページ。

ページを印刷する

1. Table of Contents

4.8 Starting and Shutting Down TRIOS IOS system

Please follow the steps below to start TRIOS IOS system for the first time:

Step 1: Turn the system ON.

S1P: Start the PC. If the PC has no TRIOS software installed, follow the

instructions in the accompanying TRIOS online help. Then start the

TRIOS software.

S1A: Press the standby button on the top of the backside of the display.

The TRIOS software starts automatically.

Step 2: Log on using a default TRIOS Operator.

Step 3: Configure and use your TRIOS IOS system.

For models with pod: S1P-2, S1P-4

The wired scanner turns on automatically when the Laptop is turn on.

For models with cart: S1A-10, S1A-12, S1A-22

The wired scanner turns on automatically when the MOVE/MOVE+ cart

is turned on.

When using the TRIOS IOS system, the user is guided by messages

shown in the TRIOS software. This includes when calibration of the

scanner is due. Other messages include a reminder to mount the

calibration adapter: "Please make sure the scanning tip is mounted

on the scanner."

Calibration

A calibration of the handheld TRIOS scanner is required before using TRIOS

IOS system for the first time and every 8 days during regular use or when the

scanner has been moved or sustained hits or strong temperature changes.

The calibration is done by placing the Calibration Tip on the Scanner Tube,

go to the Settings page in the TRIOS software, select Scan → 3D calibrate

scanner, and then follow the on-screen instructions.

For a more detailed description of the 3D calibration, please refer to the

TRIOS online help.

Color Calibration

A color calibration of the handheld scanner is required before each scan

in order to get optimal colors.

• Attach a cleaned and sterilized or high-level disinfected scanner tip

on the scanner tube.

• Remove the sleeve from the color calibration target.

• Mount the color calibration target to the calibration adaptor with

the color side, marked with the letter A, facing up.

• Attach the calibration adaptor to the cleaned and sterilized or high-level

disinfected scanner tip.

• Go to the Settings page in the TRIOS software, select TRIOS → Scanner

Management → Color calibrate scanner, and then follow the on-screen

instructions, which will also include validation of the performed color

calibration. Remember to save changes when prompted.

For a more detailed description of the color calibration, please refer

to the TRIOS online help.

Proper shutdown

Inside the TRIOS software, click on the Power button and select Shutdown

or press the the standby button on the back of the monitor on the MOVE/

MOVE+ cart.

System S1A (MOVE/MOVE+ cart) only: The light under the standby button

turns off to confirm that the system is shut down.

CAUTION

When switching off the system, allow enough time for it to

shut down properly before disconnecting the mains cable.

System S1A (MOVE/MOVE+ cart) only

IMPORTANT NOTICE

The standby button can also be used to force TRIOS IOS

system to shut down in case the screen stops responding.

To force a shutdown, push and hold the standby button

pressed for about 5 seconds. Then, restart the system.

4.9 Starting TRIOS Online Help

The TRIOS online help can be started from the TRIOS software by clicking

on the Help button and choosing User Manual.

4.10 TRIOS IOS system Environment

IMPORTANT NOTICE

Operating Conditions

Ambient temperature range: +15 – +30 °C

Relative humidity: 10 – 85 % (non-condensing)

Atmospheric pressure: 800 – 1100 hPa

The scanner should be used in an environment maintaining

a consistent room temperature.

IMPORTANT NOTICE

Storage Conditions

Ambient temperature range: -10 – +60 °C

Relative humidity: 10 – 85 % (non-condensing)

Atmospheric pressure: 800 – 1100 hPa

IMPORTANT NOTICE

Transport Conditions

Ambient temperature range: -10 – +60 °C

Relative humidity: 10 – 85 % (Non-condensing)

Atmospheric pressure: 620 – 1200 hPa

4.11 Technical specifications

Light source

Do not view directly with optical instruments, such

specifications

as spectacle microscopes. The product complies

with EN (IEC) 62471 Photobiological safety of lamps

and lamp systems.

Sterilization

Scanner tips can be autoclaved

and high-level

or high-level disinfected.

disinfection

method

Power input

C4.0/ C4.1 MOVE/MOVE+ cart (for S1A)

Power input: 100-240 VAC, 50/60 Hz, 180 VA max

Insulation class: class I

S1-2 scanner

External class I medical power supply

rated 30W max, 1.0 A.