- ページ 5

温度コントローラー dicodes Dani Extreme V2+のPDF マニュアルをオンラインで閲覧またはダウンロードできます。dicodes Dani Extreme V2+ 12 ページ。
dicodes Dani Extreme V2+ にも：マニュアル (12 ページ)

05 Main Menu (Page 2)

Battery Status

The Check Battery item shows the battery voltage with little current drained (Ub0) and the

battery voltage under load during the last puff (UbL). The difference is the voltage drop of

the battery. A high drop (>0.4V) indicates a poor battery or contact problems.

Please note that every battery has an inner resistance and that therefore the voltage at its

contacts always drops when current is drained. The more current is drained, the higher the

drop will be. Always remember this behaviour.

Commonly used batteries of 18650 size have inner resistances of about 15mOhm up to

80mOhm. Smaller sized batteries even have higher resistances. Generally speaking, the

batteries with high capacity have higher inner resistance (e.g. 2500mAh NCR has 75mOhm)

and those with lower capacity also have lower inner resistance (e.g. 2100mAh Sony Konion

has 15mOhm).

Heater Control (Operation modes)

The mod can be used in up to 5 operation modes. The mode can be selected in this menu.

The default operation is either standard (0, power setting) or temperature controlled

vaping (1). With the "Expert Mode" (Extended Functions Mod-Menu) enabled, additional

operation modes are Heater Protection (2), P

mod). With Expert Mode disabled, the menu options 2..4 are masked out.

0. Standard Mode

In the standard operation mode the wattage selected in the power setting menu is applied

to the coil, unless the voltage would be greater than 12V or the current greater than 15A,

which depends on the coil resistance.

For example with a coil resistance of 4 Ohms and a power setting of 40W, the required

voltage at the coil is 12.7V. With 4 Ohms the maximum wattage is 36W ((12V)²/4R=36W).

Or, if the coil resistance is 0.1 Ohm the maximum power is 22.5W, because (15A)²*0.1Ohm

=22.5W.

As can be seen from the examples, with high coil resistance the power is limited by

the maximum voltage of 12V and with low resistances by the maximum current of 15A.

The fact is also reflected in the feature list: A power of 40W is guaranteed from 0.2 to

3.5 Ohms. Resistances of 0.05 to 5 Ohms are possible but with a reduced power.

1. Temperature controlled vaping

In this mode the mod will regulate the temperature of the coil to the pre-set value, except

the power setting is too low to achieve the temperature. So please note to adjust the

power setting to a value high enough, if you choose temperature controlled vaping.

Otherwise the temperature regulation changes to a temperature limitation mode.

When Hctrl is set to 1, the menu directly jumps to the selection of the wire type. Here the

user can select between dicodes-wire (NiFe30), Nickel 200, Titan, Tungsten (Wolfram),

Stainless Stell (Inox) and "Other". With "Other" selected, the temperature coefficient defined

in the Extended Functions Menu under item "Tmp. Cof" is used. The value of the

selected coefficient is displayed behind "Wire". For commonly used wires, the predefined

coefficents are: NiFe30=320, Nickel200=620,Titanium=350, Tungsten=440 and Stainless

Steel=105. Note that there are different alloys for Titanium and Stainless Steel on the

market, so the predefined values can deviate from the actual wire-value you use.

ower Boost (3),

and Bypass (4, mechanical