DoorHan PCB-SW 24 프로그래밍 지침 매뉴얼 - 페이지 16
{카테고리_이름} DoorHan PCB-SW 24에 대한 프로그래밍 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DoorHan PCB-SW 24 20 페이지.
페이지 인쇄
3. OPERATOR PROGRAMMING
3.1. BASIC PROGRAMMING
Follow the below instructions to perform basic programming:
1. Enter the basic programming menu by pressing the P button. Letter P will appear at the left side of the display and the
number of menu item according to the programming table (see table 3.1) will be shown at the right side.
2. Choose the required menu item by pressing «+» and «–» buttons.
3. Press the P button to enter the menu item and the value of the set parameter will flash.
4. Press «+» and «–» to change the value of the set parameter.
5. Press the P button to save a new value and exit to the main menu.
6. After setting of all the desired parameters press the R button to exit the programming menu.
NOTE.
If it is necessary to exit to the main menu without saving the parameters, press the R button.
Menu item
P1
1 – 1 sec., 2 – 5 sec., 3 – 10 sec., 4 – 15 sec., 5 – 20 sec., 6 – 25 sec., 7 – 30 sec., 8 – 35 sec., 9 – 40 sec.
P2
Delay on closing of the 2nd door leaf: 1 – 1 sec., 2 – 2 sec., 3 – 3 sec., 4 – 4 sec., 5 – 5 sec.
P3
P4
0 – off, 1 – 10 sec., 2 – 20 sec., 3 – 30 sec., 4 – 60 sec., 5 – 90 sec., 6 – 120 sec., 7 – 180 sec., 8 – 360 sec., 9 – 420 sec.
P6
3.2. OPERATOR SETTING
The «deceleration» command is given by pressing «+» or by closing the START terminal when the door is 15-30 cm from the
door stopper.
1. Close the door leaves and block the operator (if there is a ledge set the closing/opening delay).
2. Enter the basic programming menu (see section 3.1) and choose item P3.
3. Press the P button. The display will indicate Ln, and leaf 1 will start to open.
4. When «deceleration» command is given the door leaf will slow down and a short signal will sound.
5. When leaf 1 reaches the stopper, it will stop and this position will be considered as its travel limit.
6. If one-leaf door automation is performed, the program will automatically move to item 12 or leaf 2 will start to close.
7. When «deceleration» command is given the door leaf will slow down and one short signal will sound.
8. When leaf 2 reaches the stopper, it will stop and this position will be considered as its travel limit.
9. Leaf 2 will start to close.
10. When «deceleration» command is given the door leaf will slow down and one short signal will sound.
11. When leaf 2 reaches the stopper, it will stop and this position will be considered as its travel limit.
12. Leaf 1 will start to close.
13. When «deceleration» command is given the door leaf will slow down and one short signal will sound.
14. When leaf 1 reaches the stopper, it will stop and this position will be considered as its travel limit.
15. Two short signals will sound and the program will exit programming mode.
3.3. ADVANCED PROGRAMMING
Follow the below instructions for advanced programming:
1. Press and hold the P button for 10 seconds to enter the advanced programming mode. «0» will be shown at the left side
of the display, menu item number — at the right side (see table 3.2).
2. Choose the required menu item pressing «+» and «–» buttons.
3. Press the P button to enter menu item and the value of the set parameter will flash.
4. Press «+» and «–» to change the value of the set parameter.
5. Press the P button to save a new value and exit to the main menu.
6. After setting of all the desired parameters press the R button to exit the programming menu.
16
Function description
Delay on closing of the 1st door leaf:
Automatic setting of the control board
Automatic closing of an open door in:
Cycle counter (one division — 1000 cycles)
OPERATOR PROGRAMMING
Table 3.1 Basic programming
Default
2
2
Ln
0
00