Astria Rhapsody42TEN 설치 지침 매뉴얼 - 페이지 5

{카테고리_이름} Astria Rhapsody42TEN에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Astria Rhapsody42TEN 10 페이지. 42- and 54-inch linear direct vent gas fireplaces

페이지 인쇄

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

CONNECTION AND ROUTE WIRING FOR OPTIONAL PANEL

BACKLIGHT KIT - SIT PROFLAME II SYSTEM

1. After accessing the control compartment (see Page 4, Step

1), use a screwdriver or similar object to carefully break the

sealant around the wires, taking care not to nick the wires.

2. Plug in the

Multi-wire Harness (provided with the Panel

Backlight Kit) into the SimFlame module port with the red

wires (Figures 7 and 7a)

light module harness.

Plug in the light wire harness (provided with the Panel

Backlight Kit) into the SimFlame Module port with the black

and white wires.

NOTE: If NOT installing the SimFlame (flicker) Module,

plug the Multi-Wire Harness directly into the light wire

harness (omitting the components outlined in Figure 7a)

Route the wiring up through the access opening and slide it

into the slot (Figure 8).

Attach the wiring to each lamp assembly as described

below and shown in Figure 13:

a. Route one set of three leads (white/green/black)

through the hole in the front of the bracket.

b. Connect the green wire as shown in Figure 14.

c. Insert the lamp (with green wire attached) into the

bracket until the spring clip is engaged.

d. Attach the white (neutral) and black (hot) wires as

shown in Figure 15

Carefully lay the Panel Backlight lamp assemblies and

wiring on the fireplace floor. The lamp assemblies will not

be installed until the back panel is installed

Figure

16).

Light Wire Harness

Light Module Harness

Figure 7a: Connecting the SIT PF II Module

and the light wire harness into the

(In Step 9,

SimFlame Module

Multi-Wire Harness

Red Wires

PF2 Module

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Install back panel (from required firebox liner kit)

1. Insert the bottom edge of the back panel into the fireplace

first, then position it in front of the previously installed

reflector (Figure 11).

NOTE: Lift the back panel over the tabs on the rear ledge of the fireplace.

2. Align the screw holes in the top and bottom edges of the

back panel with the holes in the fireplace ceiling and rear

ledge. Secure using seven (7) #10-16 x 3/8 hex-head sheet

metal screws provided with the firebox liner kit.

Left Side

Panel

Tab

Rear Ledge

Fireplace

Front

Figure 11: Installing the back panel

Route wiring for optional blower kit

NOTE: Use only original, factory-supplied wiring inside the

fireplace. See the wiring diagrams on Page 9.

1. Route the wiring per the instructions (P/N 750028M).

Route wiring for optional power vent kit

NOTE: Use only original, factory-supplied wiring inside the

fireplace. See the wiring diagrams on Page 9.

1. Route the wiring per instructions (P/N 506022-01).

Determine optional firebox liner backlight kit wire

routing method

There are two approved methods for routing the wiring for the

optional firebox liner backlight kit.

The preferred method is outlined in the following sections. The

alternate method is included for installations where the firebox

rear ledge does not have backlight wire routing holes, and is

described in the Appendix section Route and connect optional

firebox liner backlight kit wiring and install lamp assemblies

on Page 10.

1. Determine whether the firebox rear ledge has backlight wire

routing holes (Figure 12).

Reflector

Back Panel