Bose Acoustimass 6 Series III 소유자 매뉴얼 - 페이지 10

{카테고리_이름} Bose Acoustimass 6 Series III에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bose Acoustimass 6 Series III 23 페이지. Home theater speaker sytem
Bose Acoustimass 6 Series III에 대해서도 마찬가지입니다: 소유자 매뉴얼 (18 페이지), 빠른 설정 매뉴얼 (1 페이지), 소유자 매뉴얼 (44 페이지), 소유자 매뉴얼 (16 페이지), 소유자 매뉴얼 (25 페이지)

페이지 인쇄
Bose Acoustimass 6 Series III 소유자 매뉴얼
Figure 6). The system i
on the &her. The
ts ~~~~~t~~~ly re
cable jacket with
* Do not connect the powered AcorMimass
module directly to your TV unless /he
TV provides surround decoding circuir'vy and amplified o
uts for all channels.
1~ Inserl: -khe ~ul~i-~i~ ~~n~~~~~~ cm %he ~y~~~~ inpu% 6:
into the input jack can the ~~Q~~-
ule. ~i~h~~~ the two ~h~~~~~y~w~ to ~~~~~~ a ~~~ur~ ~~~~~~~i~~~
2,
ucxeivcx, ~~~~~ully rnakh "the ~~l~ri~y of %he ~~~~~~~i~~~ (+ to + and -~ to -)"
* ~~~~~h each ~~~~~~ wire (+) ts "dhe ~~~~~~ri~~~ t- ~~~~~~~~~
a The RCA plug of the system inpuf cable comes wifh a couer installed. Remove this
cove; for connection to the LFEXYJB!NOBFER OUTjack. If your receiver has no LFE/SUB-
WOOFER OIJTjack, leave Che plug cover in place.
3.
CA plug cm the ~y~~~~ inpud ca
FE
UT jack m your ~~r~~~tl~ rxxx%vfx
a Do not allovv exposed wires ii? brush against each other; this could damage your
receivet:
Connecting the Acoustimass@ module
to
the receiver
The 20-foot (6.1 m) system input cable connects the module to your surround receiver (see
Figure 6). The system input cable has a multi-pin connector on one end and several wire pairs
on the other. The wire pairs of the cable may be separated or "unzipped" as much as needed
to comfortably reach the surround receiver connections. Each wire pair is marked on the
cable jacket with RIGHT, LEfT, CENTER, RIGHT SURROUND or LEfT SURROUND to indi-
cate where each wire connects to the receiver.
A
CAUTHON: Before making any connections tum off your receiver and unplug it from the AC
(mains) outlet. Not doing so may result in damage to your system.
A
CAUTHON: Do not connect the powered Acoustimass module directly to your TV unless the
TV provides surround decoding circuitry and amplified outputs for all channels.
1.
Insert the multi-pin connector on the system input cable into the input jack on the Acous-
timass module. Tighten the two thumbscrews to assure a secure connection.
2.
Connect each wire pair on the other end of the system input cable to your surround
receiver. Carefully match the polarity of the connections (+ to + and -. to -).
o
Attach each marked wire (+) to the appropriate + terminal.
o
Attach each plain wire
H
to the appropriate
~
terminal.
j
N@te: The RCA plug
of the system input cable comes with a cover installed. Remove this
cover for connection to the LFE/SUBWOOFER OUTjack.
If
your receiver has
no
LFE/SUB-
WOOFER OUT jack, leave the plug cover in place.
S.
If applicable, connect the RCA plug on the system input cable to the LFE/SUBWOOFER
OUT jack on your surround receiver.
A
CAUTION: Do not allow exposed wires to brush against each other; this Gould damage your
receiver
10