Consort CRXSL-05 설치 및 사용자 설명서 - 페이지 4

{카테고리_이름} Consort CRXSL-05에 대한 설치 및 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Consort CRXSL-05 6 페이지. Single zone wireless controller

페이지 인쇄

12. Copy day function

The CRXSL allows you to copy a day's heating programme to

save time re-entering the same time and temperature settings

for each day.

This function is only available when in 7 day mode.

1. To use the copy day function, enter the programming

mode.

2. Press

to activate the COPY DAY function.

3. Press

to select the day you want to copy the

temperature settings from.

4. Press

to select the day you want to copy the

temperature settings to.

5. Press

to confirm the selection.

The 'to' word will flash to indicate that the day programme

has been copied to the day selected.

Press

to go back to the Programme mode.

13. Fan speed settings (Selected fan heaters only)

Each operating mode MANUAL, BOOST, SETBACK and

PROGRAM remembers its own fan speed setting. This speed

setting is used whenever the heating is active in that mode.

The default fan speed is medium speed for MANUAL,

SETBACK and PROGRAM modes, and high speed for BOOST.

To adjust the fan speed setting, press

active to cycle through fan speeds. For the purposes of

setting the fan speed, the heating can be made active by

temporarily increasing the set temperature.

14. Status light on the heater

Light colour

Heater status

Heater is in stand-by mode/ not

receiving signal from CRXSL.

Reduced heat output (RX only)

Full power heat output

Heater is ready for pairing with

CRXSL see section 3 "Pairing" for

details.

FAULT - Overheating (RX only)

15. RXREC compatibility mode

If the CRXSL is used with an RXREC, compatibility mode should

be used. To enable, a setting in the setup menu needs to be

changed (see section 23).

Setting 14 should be changed to 1 to enable.

16. MRX1 Multizone controller

The CRXSL controller is compatible with the MRX1 Multizone

controller. Please refer to the instructions of the MRX1 when

connecting the CRXSL controller to the MRX1.

I3984133 Iss 05

17. Choosing a position in a room

The CRXSL should be fixed to the wall or used with the table

top stand. Avoid areas with draught or direct sun. Do not

position CRXSL above or close to the heaters or other heat

sources. Damp areas or areas where CRXSL can be

mechanically damaged should also be avoided.

18. Power options

Please note that the controller screen will take up to

one minute to display after powering up for the FIRST

time.

The CRXSL controller can be powered either by a 5V power

adapter with a micro USB connector, supplied power

adapter via USB port or 4 AAA batteries. There are 2

available USB ports for power. One port is located on the

bottom and one at the back of the controller.

The display will show the battery status only when the CRXSL

is powered by batteries alone.

when heating is

19. Batteries

Remove the CRXSL's battery cover and insert 4 new high

quality alkaline AAA batteries.

Warning: Consort is not responsible for damage due to

corrosion. Battery leakage will cause permanent damage.

To help avoid battery leak:

•

Note: The clock has to be set after replacing the batteries, or

if the USB power cable has been disconnected from the

CRXSL or power to the power adapter switched off. This does

not apply if it is being used with the MRX1 Multizone

controller. If the CRXSL is powered by the power adapter,

2 AAA batteries can be used to supply power in the event of

a power cut in order to keep the clock running. The batteries

should be replaced annually.

Replace the batteries annually, even if there is not a

low battery warning. Remove failing or flat batteries

immediately.

Always fit new high quality alkaline batteries from the

same pack. Never mix new and old batteries, or

batteries of different brands or types.

Never attempt to revive alkaline batteries by heating,

crushing or recharging.