ADEMCO Counterforce CFV15P 프로그래밍 매뉴얼 - 페이지 8

{카테고리_이름} ADEMCO Counterforce CFV15P에 대한 프로그래밍 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO Counterforce CFV15P 16 페이지.

페이지 인쇄

Configurable Zone Types Worksheets

Configurable zone types 90 and 91 can be programmed via downloader software or from a keypad using data

fields*182-*185.

Programming Configurable Zone Type options involves making 10 entries in data field *182 for zone type 90 and

field *184 for zone type 91, where each entry represents the sum of the values of the various options shown in the

tables below. Use fields *183 and *185 to program Contact ID report codes for these zone types.

ENTRY 1

(See note 5 for RF

zones)

Response when system disarmed and zone is:

Intact EOL

Open

RF zone normal

RF zone N/A

0 = normal

1 = alarm

4 = alarm

2 = trouble

8 = trouble

3 = fault

12 = fault

Entry 1 = EOL + Open

ENTRY 3

(See note 5 for RF zones)

Response when armed STAY and zone is:

Intact EOL

Open

RF zone normal

RF zone N/A

0 = normal

1 = alarm

4 = alarm

2 = trouble

8 = trouble

3 = fault

12 = fault

Entry 3 = EOL + Open

ENTRY 5

(See note 5 for RF zones)

Response when armed AWAY and zone is:

Intact EOL

Open

RF zone normal

RF zone N/A

0 = normal

1 = alarm

4 = alarm

2 = trouble

8 = trouble

3 = fault

12 = fault

Entry 5 = EOL + Open

ENTRY 7

Display Faults

Power Reset/

Verification

0 = show alarms

0 = no

when armed

4 = power reset

& disarmed

after fault

1 = don't show

(by code + OFF)

12 = verification

alarms when

(see zone

armed

(show

type 16)

alarms, trbles,

faults when

disarmed)

3 = never show

any alarms,

trbles, faults

Entry 7 = fault display + power

reset/verification

ENTRY 9

Alarm Sounds

Use Bell

Timeout

0 = none

0 = no

1 = steady

4 = yes

keypad

2 = steady bell

see fields *32,

and keypad

*33

3 = pulsing bell

and keypad

Entry 9 = alarm sounds + bell timeout + fire zone

ENTRY 2

(See note 5 for RF zones)

Auto

Restore

Shorted

RF zn off-normal

0 = normal

0 = no

1 = alarm

4 = yes

2 = trouble

3 = fault

Entry 2 = Short + auto restore + vent zone

ENTRY 4

(See note 5 for RF zones)

Byp. when

disarmed

Shorted

RF zn off-normal

0 = normal

0 = no

1 = alarm

4 = yes

2 = trouble

3 = fault

Entry 4 = Short + byp. disarmed + byp. armed

ENTRY 6

(See note 5 for RF zones)

Dial Delay

(see field *50)

Shorted

RF zn off-normal

0 = normal

0 = no

1 = alarm

4 = use delay

2 = trouble

3 = fault

Entry 6 = Short + dial delay + fault delay

ENTRY 8

Use Entry

Use Exit

Delay 1/2

Delay

0 = no

1 = delay 1

4 = use exit

2 = delay 2

delay

Entry 8 = entry delay 1/entry delay 2 + exit delay +

interior zone type

ENTRY 10

Respond as

Trouble

Fire Zone

Sounds

0 = no

0 = none

8 = yes

1 = periodic

beep

see zone type

2 = trouble

09; see note 4

beeps

Entry 10 = trouble sounds + chime

Entry Zone Type 90

Vent Zone

0 = no

8 = yes

Byp. when

armed

0 = no

To calculate the value for each entry:

8 = yes

Simply add the values of the selected options

in each of the entry's columns (one option per

column). For example, to program Entry 2 for

"alarm response to short," "auto restore on,"

but not a "vent zone," enter 5 ("1" for alarm

short + "4" for auto restore yes + "0" for vent

Fault Delay

zone no).

(see field *87)

0 = no

8 = use delay

see note 1

Respond as

Interior Type

NOTES:

0 = no

1. Do not use the "fault delay" option with a

8 = yes

see note 2

2. To create an interior type zone, select

3. Do not set fire zones to respond as a

4. 4219/4229 modules must use EOLRs or

Chime when

Chime Mode On

5. RF Zones: The "open" option in entries 1,

0 = no

4 = yes

– 8 –

Entries for Fields *182 and *184

Zone Type 91

(field *182)

(field *184)

INTACT

OPEN

SHORTED

EOL

ZONE-003-V0

Zone Conditions Represented

in Entries 1-6

configurable zone type if it is set for an

entry or exit delay, otherwise

unpredictable results may occur.

"respond as interior zone type" (entry 8,

interior type = yes), and set zone

response to "fault" in entries 3-4 to ensure

fault displays; do not set as "normal,"

"alarm," or "trouble."

"fault" (entries 1-6), otherwise faults will

not display unless the [∗] key is pressed.

unpredictable results may occur.

3, and 5 is not applicable for RF zones.

Use the "intact EOL" option for normal RF

zone conditions and "shorted" for off-

normal RF zone conditions.