ADEMCO Vista-10P 프로그래밍 매뉴얼 - 페이지 2

{카테고리_이름} ADEMCO Vista-10P에 대한 프로그래밍 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO Vista-10P 17 페이지. Alarm control panel

페이지 인쇄

TO ENTER PROGRAMMING MODE:

Local programming requires the use of an alpha keypad connected to the keypad terminals on the control.

A. POWER UP, then depress [ ] and [#] both at once, within 50 seconds of powering up )if

must be used to reenter program mode). OR

B. Initially, key: Installer Code (4 + 1 + 1 + 2) plus 8 + 0 + 0.

Data Field Programming Procedures

Task

Procedure

Press [ ∗ ] + [Field Number], followed by the required entry.

Go to a Data Field

Entering Data

When the desired field number appears, simply make the required entry. When the last entry for a field is entered,

the keypad beeps three times and automatically displays the next data field in sequence.

If the number of digits that you need to enter in a data field is less than the maximum digits available (for example,

the phone number fields *41, *42), enter the desired data, then press [ ∗ ] to end the entry. The next data field is

displayed.

Review a Data Field

Press [#] + [Field Number].

Data will be displayed for that field number. No changes will be accepted in this mode.

Press [ ∗ ] + [Field Number] + [ ∗ ]. (Applies only to fields ∗ 40–*46, *94, and pager programming fields)

Deleting an Entry

Interactive Menu Mode Programming (∗56, ∗57, ∗58, ∗79, ∗80, ∗81, ∗82)

See respective sections in this document for programming procedures.

Press [ ] + [Interactive Mode No.] (for example, 56). The alpha display keypad will display the first of a series of prompts.

Interactive Menu Mode

56 Zone Programming

57 Function Key Programming

58 Zone Programming

(Expert mode)

79 Output Device Mapping

80 Output Programming

81 Zone List Programming

82 Alpha Programming

INITIALIZE DOWNLOAD and RESET DEFAULTS

96 Initializes download ID and subscriber account number.

97 Sets all data fields to original factory default values.

TO EXIT PROGRAMMING MODE:

98 Exits programming mode and prevents re-entry by: Installer Code + 8 + 0 + 0. If 98 is used to exit programming mode,

system must be powered down, and method A above used to enter the programming mode.

See field *88 for other *98 Program mode lockout options.

99 Exits programming mode and allows re-entry by: Installer Code + 8 + 0 + 0 or method A above.

Special Messages

OC = OPEN CIRCUIT (no communication between Keypad and Control).

EE or ENTRY ERROR = ERROR (invalid field number entered; re-enter valid field number).

After powering up, AC, dI (disabled) or Busy Standby and NOT READY will be displayed after approximately 4 seconds. This will revert to

a "Ready" message in approximately 1 minute, which allows PIRS, etc. to stabilize. You can bypass this delay by pressing [#] + [0].

If E4 or E8 appears, more zones than the expansion units can handle have been programmed. The display will clear after you correct the

programming.

Table of Device Addresses

This Device

RF Receiver

Long Range Radio

4286 Voice Module

4204 Relay Module

Keypads:

keypad 1

keypad 2

keypad 3

keypad 4

keypad 5

keypad 6

keypad 7

keypad 8

5800TM Module

†† Addressable devices are identified by "1" plus the device address when reporting. Enter report code for zone 91 to enable addressable device

reporting (default = reports enabled). See field *199 for addressable device (ECP) 3-digit/2-digit identification keypad display options.

Used to Program

Zone characteristics, report codes, alpha descriptors, and serial numbers for RF trans.

Unlabeled keypad keys (known as ABCD keys) for special functions

Same options as *56 mode, but with fewer prompts. Intended for those familiar with

this type of programming, otherwise *56 mode is recommended.

Assign module addresses and map individual relays/powerline carrier devices

4204 Relay modules, Powerline Carrier devices, or on-board triggers

Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc.

Zone alpha descriptors

††

Uses Address Reports as

100

103

104

112

n/a

– 2 –

98 was used to exit previously, this method

Enabled By...

*56 zone programming: input device type entry

automatic if output to long range radio field *29 enabled

automatic if phone module access code field *28 enabled

*79 output device programming: entered at device address prompt:

data field programming as listed below:

always enabled, all sounds enabled.

data field *190

data field *191

data field *192

data field *193

data field *194

data field *195

data field *196

automatic