ADEMCO Vista-10P 프로그래밍 매뉴얼 - 페이지 3

{카테고리_이름} ADEMCO Vista-10P에 대한 프로그래밍 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO Vista-10P 17 페이지. Alarm control panel

Entry of a number other than one specified will give unpredictable results. Values shown in brackets are factory defaults.

Field

Title / Valid Entries

SYSTEM SETUP

∗20

Installer Code

4 digits, 0–9. Can perform all system functions except

cannot disarm unless it is used to arm system.

∗21

Quick Arm Enable

0 = no quick arm; 1 = allow quick arm (with [#] key)

∗22

RF Jam Option

0 = no RF Jam detection

1 = send RF Jam report upon detection of RF jamming

signal UL: must be 1 if wireless devices are used

∗23

Quick (Forced) Bypass

0 = no quick bypass UL: must be "0"

1 = allow quick bypass (code + [6] + [#] )

∗24

RF House ID Code

00 = disable all wireless keypad usage

01–31 = house ID for 5827, 5827BD or 5804BD keypad

∗26

Chime By Zone

0 = no (chimes on fault of any entry/exit or perimeter zone

when chime mode on);

1 = use zone list (chimes on fault of specific zones

programmed in relay zone list 3 when Chime mode on;

use *81 Menu mode to select zones)

∗28

Access Code For Phone Module

00 = disable; UL: must be "00" for UL Commercial Burg. inst.

1st digit: enter 1–9;

2nd digit: enter # + 11 for " ", or # + 12 for "#".

∗29

Long Range Radio Output

0 = not using LORRA; 1 = using LORRA output

ZONE SOUNDS AND TIMING ( 31 – 39)

∗31

One Audible Alarm Per Zone

0 = no UL: must be "0"; 1 = yes

∗32

Fire Alarm Sounder Timeout

0 = sounder stops at timeout programmed in field ∗33

1 = no sounder timeout UL: must be "1" for fire install.

∗33

Alarm Sounder (Bell) Timeout

0 = none; 1 = 4 min; 2 = 8 min; 3 = 12 min; 4 = 16 min;

UL: For residential fire alarm installation, must be set for a minimum

of 4 min (option 1); for UL Commercial Burglary installations, must

be minimum 16 min (option 4)

∗34

Exit Delay

00 - 96 = 0 - 96 secs; 97 = 120 secs

SIA Installations: minimum exit delay is 45 seconds

UL: see inst. instr. for requirements.

∗35

Entry Delay #1

(zone type 01)

00 - 96 = 0 - 96 seconds

97 = 120 seconds

98 = 180 seconds

99 = 240 seconds

For UL Residential Burglary Alarm installations, must be set for a

maximum of 30 seconds; entry delay plus dial delay should not

exceed 1 min. For UL Commercial Burglar Alarm, total entry delay

may not exceed 45 seconds.

352*5$00,1*)250

Programmed Values

[4112]

[0]

[00]

[0]

[00]

[0]

[1]

[60]

[30]

SIA Installations:

minimum entry delay is

30 seconds

∗36

Entry Delay #2

See *35 Entry Delay 1 above for entries.

∗37

Audible Exit Warning

0 = no; 1 = yes

SIA Installations: must be enabled (enter 1)

∗38

Confirmation Of Arming Ding

0 = no ding

1 = confirmation ding after arming system

2 = ding after arming from RF button or RF keypad only

UL: must be "1" for UL Commercial Burglar Alarm inst.

∗39

Power Up In Previous State

0 = always power-up in a disarmed state

1 = assume the system status prior to power down

UL: must be "1"

DIALER PROGRAMMING

Enter the number of digits shown. Do not fill unused spaces. Enter

0–9; #+11 for ' '; #+12 for '#'; #+13 for a 2-second pause. If fewer

than the maximum digits entered, exit the field by pressing [ ]. The

next field number is displayed.

∗40

PABX Access Code

Enter up to 6 digits. To clear entries, press 40 .

If call waiting used, enter "∗ (#+11) 70" plus "# + 13" (pause).

∗41

Primary Phone No.

| | | | | | | | | | | | | | | | | | |

∗42

Second Phone No.

| | | | | | | | | | | | | | | | | | |

Enter up to 20 digits. To clear entries, press 41 or

respectively .

NOTE: Entry of a number other than one specified will give

unpredictable results.

For fields *43- *46: Enter 0–9; #+11 for B; #+12 for C; #+13 for D; #+14 for E;

#+15 for F. Enter [ ] as the fourth digit if a 3-digit account number (for 3+1

dialer reporting format) is used. Enter 0 as the first digit of a 4-digit account

number for Nos. 0000-0999. Exit field by pressing

number) if only 3 digits are used. E.g., For Acct. B234, enter:

#+11| 2 | 3 | 4

∗43

Primary Subs. Acct. No.

| | | /

| | | | |

depending on selection in *48 Report Format. See box

above for entries. To clear entries, press * 43 *.

∗44

Secondary Subs. Acct. No.

| | | /

| | | | |

* 44 * .

∗47

Phone System Select

DIALING

NOT On WATS LINE

Pulse Dial

Tone Dial

∗48

Report Format

0 = 3+1, 4+1 ADEMCO L/S STANDARD

1 = 3+1, 4+1 RADIONICS STANDARD

2 = 4+2 ADEMCO L/S STANDARD

3 = 4+2 RADIONICS STANDARD

5 = 10-digit ADEMCO CONTACT ID® REPORTING

6 = 4+2 ADEMCO EXPRESS

7 = 4-digit ADEMCO CONTACT ID® REPORTING

8 = 3+1, 4+1 ADEMCO L/S EXPANDED

9 = 3+1, 4+1 RADIONICS EXPANDED

– 3 –

(zone type 02)

(and press next field

[FFFF] Enter 4 or 10 digits,

[FFFF] See *43. To clear, press

USING WATS LINE

[77]

Primary Second

[30]

[1]

[0]

[1]