ADEMCO Vista-10P 프로그래밍 매뉴얼 - 페이지 4

{카테고리_이름} ADEMCO Vista-10P에 대한 프로그래밍 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO Vista-10P 17 페이지. Alarm control panel

페이지 인쇄

∗49

Split/Dual Reporting

0 = Standard/Backup reporting only (all to primary unless fail)

Primary Phone No.

1 = Alarms, Restore, Cancel

2 = All except Open/Close, Test Open/Close, Test

3 = Alarms, Restore, Cancel

4 = All except Open/Close, Test All

5 = All

∗50

Burglary Dialer Delay

0 = no delay UL: must be "0"

1 = 15 seconds

2 = 30 seconds

3 = 45 seconds

∗53

SESCOA/Radionics Select

0 = Radionics (0-9, B-F), and all formats other than SESCOA

1 = SESCOA (0-9 only reporting)

∗54

Dynamic Signaling Delay

Delay selectable from 0 to 225 secs in 15-sec increments.

0 = no delay (both signals sent),

1 = 15 secs,

2 = 30 secs, etc

UL: Grade AA must be "0;" Grade A must be "15" max

∗55

Dynamic Signaling Priority

0 = Primary Dialer first; 1 = Long Range Radio first.

For UL Commercial Burglary installations that use a DACT

and LRR, this field must be "0".

∗56 -*58

Menu Modes (see page 2 for description)

PROGRAMMING SYSTEM STATUS, & RESTORE REPORT

CODES ( 59 – 76, & 89):

For 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–

9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15

for F.

A 0 ( not #+10) in the first box will disable a report. A 0 ( not #+10) in

the second box will result in automatic advance to the next field.

For Expanded or 4+2 Format: Enter codes in both boxes (1st and

2nd digits) for 1–9, 0, or B–F, as described above.

A 0 ( not #+10) in the second box will eliminate the expanded

message for that report. A 0 ( not #+10) in both boxes will disable

the report.

For Ademco Contact ID® Reporting: Enter any digit (other than 0)

in the first box, to enable zone to report (entries in the second boxes

are ignored).

A 0 ( not #+10) in the first box disables the report.

UL: see installation instructions for requirements

SYSTEM STATUS REPORT CODES

∗59

Exit Error Report Code

∗60

Trouble Report Code

∗61

Bypass Report Code

∗62

AC Loss Report Code

∗63

Low Bat Report Code

∗64

Test Report Code

Use Scheduling mode to set periodic test reports or use the

following key commands to set schedule 2 to the stated

repeat option (first test report sent 12 hours after command):

installer code +[#] + [0] + 0 = test report sent every 24 hours

installer code +[#] + [0] + 1 = test report sent once per week

installer code +[#] + [0] + 2 = test report sent every 28 days

∗65

Open Report Code

∗66

Arm Away/Stay Rpt Code

[0]

2nd Phone No.

Others

All

[2]

SIA Installations: delay

must be minimum of

30 seconds

[0]

[00]

[0]

[0,0]

Away Stay

∗67

RF Trans. Low Bat Report Code

UL: must be enabled if wireless devices are used

∗68

Cancel Report Code

RESTORE REPORT CODES

∗70

Alarm Restore Rpt Code

∗71

Trouble Restore Rpt Code

∗72

Bypass Restore Rpt Code

∗73

AC Restore Rpt Code

∗74

Low Bat Restore Rpt Code

∗75

RF Trans. Lo Bat Rst Rpt Code

UL: must be enabled if wireless devices are used

∗76

Test Restore Rpt Code

OUTPUT AND SYSTEM SETUP

∗77

Daylight Savings Time

Start\End Month

0 = Disabled

1-9 = January-September (1 = Jan, 2 = Feb, etc)

#+10 = October; #+11 = November; #+12 = December

∗78

Daylight Savings Time

Start\End Weekend

0 = disabled, 1 = first, 2 = second, 3 = third

4 = fourth, 5 = last, 6 = next to last, 7 = third to last

∗79 -*82

Menu Modes (see page 2 for description)

∗84

Auto Stay Arm

0 = no, 1 = yes, auto stay arm enabled

∗85

Cross Zone Timer

This option not for use in UL installations.

0 = 15 seconds

1 = 30 seconds

2 = 45 seconds

3 = 60 seconds

4 = 90 seconds

5 = 2 minutes

(assign cross zones on zone list 4, with *81 Menu mode)

∗86

Cancel Verify Keypad Display

0 = no, 1 = yes

∗87

Misc. Fault Delay Time

(used with Configurable Zone Type "digit 6")

0 = 15 seconds

1 = 30 seconds

2 = 45 seconds

3 = 60 seconds

4 = 90 seconds

5 = 2 minutes

UL: may only be used on non-burglar alarm/ non-fire alarm zones

when used in fire and/or UL burglar alarm installation

∗88

Program Mode Lockout Options

0 = standard *98 installer code lockout

(reentry only by [∗] + [#] within 50 seconds after power up)

1 = lockout [∗] + [#] reentry after *98 exit

2 = not used

3 = lockout all local programming after *98 exit (reentry via

downloader only)

– 4 –

[00]

[0]

[00]

[4][10]

[1][5]

[1]

[0]

6 = 2-1/2 min

#+12 = 8 min

7 = 3 min

#+13 = 10 min

8 = 4 min

#+14 = 12 min

9 = 5 min

#+15 = 15 min

#+10 = 6 min

#+11 = 7 min

[1]

[0]

6 = 2-1/2 min

#+12 = 8 min

7 = 3 min

#+13 = 10 min

8 = 4 min

#+14 = 12 min

9 = 5 min

#+15 = 15 min

#+10 = 6 min

#+11 = 7 min

[0]