Gardena PowerJet Li-40 운영자 매뉴얼 - 페이지 3
{카테고리_이름} Gardena PowerJet Li-40에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Gardena PowerJet Li-40 18 페이지. Battery blower / vacuum
Gardena PowerJet Li-40에 대해서도 마찬가지입니다: 운영자 매뉴얼 (18 페이지), 운영자 매뉴얼 (18 페이지)
페이지 인쇄
2 Preparation
a) Obtain ear protection and safety glasses. Wear them
at all times while operating the machine.
b) While operating the machine always wear substantial
footwear and long trousers. Do not operate the
machine when barefoot or wearing open sandals.
Avoid wearing clothing that is loose fitting or that
has hanging cords or ties.
c) Do not wear loose clothing or jewellery that can be
drawn into the air inlet. Keep long hair away from the
air inlets.
d) Operate the machine in a recommended position and
only on a firm, level surface.
e) Do not operate the machine on a paved or gravel sur-
face where ejected material could cause injury.
f) Before using, always visually inspect to see, that the
shredding means, shredding means bolts and other
fasteners are secure, the housing is undamaged and
that guards and screens are in place. Replace worn or
damaged components in sets to preserve balance.
Replace damaged or unreadable labels.
g) Before use, check the supply and extension cord for
signs of damage or aging. If the cord becomes dam-
aged during use, disconnect the cord from the supply
immediately.
DO NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY.
Do not use the machine if the cord is damaged or
worn.
h) Never operate the machine while people, especially
children, or pets are nearby.
3 Operation
a) Before starting the machine, make certain that the
feeding chamber is empty.
b) Keep your face and body away from the feed intake
opening.
c) Do not allow hands or any other part of the body or
clothing inside the feeding chamber, discharge chute,
or near any moving part.
d) Keep proper balance and footing at all times. Do not
overreach. Never stand at a higher level than the base
of the machine when feeding material into it.
e) Always stand clear of the discharge zone when oper-
ating this machine.
f) When feeding material into the machine be extremely
careful that pieces of metal, rocks, bottles, cans or
other foreign objects are not included.
g) If the cutting mechanism strikes any foreign objects
or if the machine should start making any unusual
noise or vibration, immediately shut off the power
source and allow the machine to stop.
Disconnect the machine from the supply and take
the following steps before restarting and operating the
machine:
– inspect for damage;
– replace or repair any damaged parts;
– check for and tighten any loose parts.
h) Do not allow processed material to build up in the dis-
charge zone; this may prevent proper discharge and
can result in kickback of material through the intake
opening.
i) If the machine becomes clogged, shut-off the power
source and disconnect the machine from supply
before cleaning debris.
j) Never operate the machine with defective guards or
shields, or without safety devices, for example debris
collector in place.
k) Keep the power source clean of debris and other
accumulations to prevent damage to the power source
or possible fire.
l) Do not transport this machine while the power source
is running.
m) Stop the machine, and remove plug from the socket.
Make sure that all moving parts have come to a com-
plete stop
– whenever you leave the machine,
– before clearing blockages or unclogging chute,
– before checking, cleaning or working on the
machine.
n) Do not tilt the machine while the power source is
running.
4 Maintenance and storage
a) When the machine is stopped for servicing, inspection,
or storage, or to change an accessory, shut off the
power source, disconnect the machine from the sup-
ply and make sure that all moving parts are come to
a complete stop. Allow the machine to cool before
making any inspections, adjustments, etc. Maintain the
machine with care and keep it clean.
b) Store the machine in a dry place out of the reach of
children.
c) Always allow the machine to cool before storing.
d) When servicing the shredding means be aware that,
even though the power source is switched off due
to the interlock feature of the guard, the shredding
means can still be moved.
e) Replace worn or damaged parts for safety. Use only
genuine replacement parts and accessories.
f) Never attempt to override the interlocked feature of the
guard.
5 Additional safety instructions for units
with bagging attachments
Switch-off the machine before attaching or removing the
bag.
Additional safety warnings
Battery safety
DANGER! Fire risk!
The battery to be charged must be placed on
a nonflammable, heat resistant and non-conduc-
tive surface while charging.
Keep corrosive, flammable and easily combus-
tible objects clear of the battery charger and the
battery.
15