Garmin Reactor 40 설치 지침 매뉴얼 - 페이지 5
{카테고리_이름} Garmin Reactor 40에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin Reactor 40 13 페이지. Mechanical
Garmin Reactor 40에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (11 페이지), 설치 지침 매뉴얼 (29 페이지), 구성 매뉴얼 (8 페이지), 설치 지침 매뉴얼 (25 페이지)
페이지 인쇄
Item
Description
Splice
10 AWG (5.26 mm²) extension wire
Fuse
8 in. (20.3 cm)
Battery
8 in. (20.3 cm)
Up to 15 ft. (4.6 m)
Item
Description
Splice
8 AWG (8.36 mm²) extension wire
Fuse
8 in. (20.3 cm)
Battery
8 in. (20.3 cm)
Up to 23 ft. (7 m)
Item
Description
Splice
6 AWG (13.29 mm²) extension wire
Fuse
8 in. (20.3 cm)
Battery
8 in. (20.3 cm)
Up to 36 ft. (11 m)
Installing a Garmin Rudder Feedback Sensor
If you installed a drive unit provided by Garmin, rudder feedback
data is provided by the drive unit, and a separate rudder
feedback sensor is not required. If you are connecting the
autopilot to a drive unit not sold by Garmin, you must also install
a rudder feedback sensor, such as the GRF 10 (sold
separately).
Follow the installation instructions provided with your GRF
rudder feedback sensor to connect it to your rudder control
and autopilot system.
Drive Unit Installation
The drive unit (sold separately) must be connected to your
rudder control so the Reactor 40 Mechanical autopilot can steer
your boat. When you purchase a drive unit sold by Garmin, it will
include the correct cables, connectors, and instructions.
If a drive unit is installed on your boat already, you can use a
drive unit power cable (sold separately) to adapt your drive unit
for use with the autopilot system.
If you connect the autopilot system to a drive unit not sold by
Garmin, you must also provide rudder-feedback information by
installing and connecting a Garmin rudder-feedback sensor
(recommended) or by connecting to an existing rudder-feedback
sensor on your boat using a rudder feedback cable (sold
separately).
Installing a Garmin Drive Unit
Follow the installation instructions provided with your Garmin
drive unit to mount it and connect it to your rudder control and
autopilot system.
Connecting to an Existing Drive Unit
You must install a drive unit power cable to use a drive unit not
sold by Garmin with the Reactor 40 Mechanical autopilot. This
cable is sold separately.
These instructions do not apply to a solenoid-type drive unit
(Connecting to a Solenoid Drive Unit, page
1
If necessary, use the installation instructions provided with
the drive unit to install it on your boat.
2
If your drive unit has cables connected, disconnect the
cables.
3
Consult the documentation provided by the manufacturer of
your drive unit to identify the connections on your drive unit.
4
Connect the drive unit power cable (not included) to your
drive unit, based on the wire colors and functions in the table.
The drive unit power cable cannot be extended.
Wire Color Function
Red
Drive unit positive (+)
Black
Drive unit negative (-)
Blue
Clutch power (cut and tape this wire if your drive unit
has no clutch)
White
Clutch ground (cut and tape this wire if your drive unit
has no clutch)
5
Connect the drive unit power cable to the ECU.
Connecting to a Solenoid Drive Unit
You must install the solenoid power cable to use a solenoid
drive unit with theReactor 40 Mechanical autopilot system. This
cable is sold separately.
These instructions apply only to solenoid-type drive units.
1
If necessary, use the installation instructions provided with
the solenoid drive unit to install it on your boat.
2
If your solenoid drive unit has cables connected, disconnect
the cables.
3
Consult the documentation provided by the manufacturer of
your solenoid drive unit to identify the connections on your
drive unit.
4
Connect the solenoid power cable (not included) to your
solenoid drive unit, based on the diagram and tables.
The solenoid power cable is 0.8 m (2.6 ft.) long, and cannot
be extended.
5).
5