Dexter Laundry WCAD Series 프로그래밍 지침 매뉴얼 - 페이지 3

{카테고리_이름} Dexter Laundry WCAD Series에 대한 프로그래밍 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dexter Laundry WCAD Series 6 페이지. Vended washers

페이지 인쇄

#4 Warm Water Price: The next step in the pricing program is to set the additional price for Warm

water usage. The display will blink ﬁ rst "CH P" indicating cold/hot water mix price and then "00.00".

To change the value, use the Hot temperature button to decrease and the Warm temperature button

to increase. The value will change in 1¢ steps. The range of values is from $00.00 to $99.99.

NOTE:

To not use this feature, set the price to "00.00".

When the desired price is displayed, push the Start button once to store the new value and a second

time to move to the next Coin/Price programming step. To exit the Coin/Price programming mode,

push the Cold temperature button for 5 seconds.

#5 Hot Water Price: The next step in the pricing program is to set the additional price for Hot water

usage. The display will blink ﬁ rst "H P" indicating hot water price and then "00.00". To change the

value, use the Hot temperature button to decrease and the Warm temperature button to increase.

The value will change in 1¢ steps. The range of values is from $00.00 to $99.99.

NOTE:

To not use this feature, set the price to "00.00".

When the desired price is displayed, push the Start button once to store the new value and a second

time to move to the next Coin/Price programming step. To exit the Coin/Price programming mode,

push the Cold temperature button for 5 seconds. The Coin/Price programming mode will automatically

exit and return to the Idle mode if no buttons are pushed for one minute.

#6 Plus Cycle Price: The next step in the programming sequence is the Plus Cycle feature. The Plus

Cycle adds three (3) minutes of wash time to the wash bath only. The controller can be programmed

to charge a fee for this or the feature can be turned off. The default setting is off ($0.00).

The display will blink ﬁ rst a "PC P" indicating Plus Cycle price and then price (back and forth). To

change the value, use the Hot temperature button to decrease and the Warm temperature button to

increase. The value will change in 1¢ steps. The range of values is from $00.01 to $99.99. When the

desired price is displayed, push the Start button once to store the new value and a second time to

move to the next Coin/Price programming step. To exit the Coin/Price programming mode, push the

Cold temperature button for 5 seconds.

#7 Decimal Point: The next step in the programming sequence is the Decimal Point. The display will

blink"dP" and Default value is ON. The value "on" for enable or "off" for disable. Once a pushbutton

is pressed, the display will stop blinking and show the decimal point value. The decimal point value

will display and change with the Hot and Warm buttons. When desired value is reached press Start

button.

Wash Cycle Programming

To change a feature of the wash cycle, push and hold the Hot temperature button and then push the

programming pushbutton on the controller. The Washer mush be in the Idle mode to enter the Wash Cycle

Programming mode. When entering the cycle programming mode the Bleach LED will start to blink and

continue to blink as long as you are in the Cycle Programming mode. The display will show "C 0". This is

the default cycle number.

NOTE:

The washer can be returned to the factory default settings by holding the right Warm button

and then pressing the left Warm button. The display must show "C 0" to do this. When the cycle

default values are loaded, the washer will automatically exit the programming mode.

NOTE:

The Wash Cycle programming mode will automatically exit and return to the Idle mode if no

buttons are pushed for one minute.

Part # 8533-073-001 11/11