EarthQuake E43 earth auger powerhead 운영자 매뉴얼 - 페이지 7

{카테고리_이름} EarthQuake E43 earth auger powerhead에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. EarthQuake E43 earth auger powerhead 16 페이지. Power earth auger
EarthQuake E43 earth auger powerhead에 대해서도 마찬가지입니다: 운영자 매뉴얼 (17 페이지)

페이지 인쇄

EarthQuake E43 earth auger powerhead 운영자 매뉴얼

Starting and Stopping Engine

1. Move engine to a well ventilated area, outdoors, to

prevent carbon monoxide poisoning.

2. Move to an area away from flames or sparks, to avoid

ignition of vapors if present.

3. Remove all debris from air cleaner holes and fuel cap

to ensure proper air flow.

4. Turn switch to the ON position.

5. Priming:

• When using the primer bulb, allow the bulb to return

completely to its original position between pushes.

• Choke must be in the OFF position when pushing or

using the primer bulb.

First Start: Starting new engine for first time or after

running out of gas, prime 3 times.

Cold Start: Starting engine after it has been sitting or

stored briefly with fuel in the tank, prime 1 time above 55°

Farenheit or 2 times below 55° Farenheit.

Warm Start: Do not use primer or full choke if engine did

not run out of gas or has not cooled completely. Flooding

of engine will occur.

6. Choke:

• Full choke position is defined by moving the choke lever

as far to the ON position as possible. Half choke is

defined when the choke lever is between ON and OFF.

First Start & Cold Start: After priming, move choke lever

to full choke.

Warm Start: No choke or half choke is needed.

Avoid injury! Starter rope can cause an unanticipated

jerk towards engine. Please follow instructions to

avoid injury.

7. Grasp starter handle and pull out slowly, until it pulls

slightly harder. Without letting it retract, pull rope with a rapid

full arm stroke. Let it return to its original position very

slowly. Repeat this step everytime the starter rope is pulled.

1-800-345-6007

OPERA

OPERATION

OPERA

TION

OPERA

TION

CAUTION

8. Pull recoil until engine fires or runs.

NOTE: If engine fails to start after 5-6 pulls, push

primer 1 time and pull starter rope again.

9. After engine starts running, move choke lever to HALF

CHOKE.

10. Run engine for 30 to 45 seconds at half choke position

until engine warms up.

11. Move choke lever to OFF position and move throttle to

desired speed.

12. To stop, flip switch to OFF position.

Avoid injury! If engine fails to start after the above

operations, please contact Ardisam, Inc. at 1-800-345-

6007.

DO NOT attempt to start engine in the following ways:

• • • • • DO NOT use starting fluid.

• • • • • DO NOT spray flammable liquids or vapors into air

cleaner, carburetor or spark plug chamber.

• • • • • DO NOT remove spark plug and pull on starter

rope. Flammable fuel can spray out & ignite from a

spark from spark plug.

Avoid injury! Never leave engine running while

unattended. Turn off after every use.

Avoid injury! Never carry powerhead and auger

between holes while engine is running.

Normal Operation

1. The clutch will transfer maximum power after

about two hours of normal operation. During this break-in

period clutch slippage may occur. The clutch should be

kept free of oil and other moisture for efficient operation.

2. Dig holes without placing excessive body weight on the

unit. The auger operates most efficiently with a shaving

action caused by the weight of the unit itself.

3. Never run engine indoors. Exhaust fumes are deadly.

Page 7

CAUTION