HP StorageWorks 1000 - Modular Smart Array 설치 - 페이지 2

{카테고리_이름} HP StorageWorks 1000 - Modular Smart Array에 대한 설치을 온라인으로 검색하거나 PDF를 다운로드하세요. HP StorageWorks 1000 - Modular Smart Array 4 페이지. Power supply, computer
HP StorageWorks 1000 - Modular Smart Array에 대해서도 마찬가지입니다: 네트워크 매뉴얼 (8 페이지), 지원 목록 (34 페이지), 오류 방지 매뉴얼 (12 페이지), 기술 백서 (12 페이지), 펌웨어 업데이트 (9 페이지), 개요 (20 페이지), 설치 매뉴얼 (2 페이지), 지원 전화번호 (19 페이지), 참조 매뉴얼 (48 페이지), 관리 매뉴얼 (40 페이지), 릴리스 노트 (13 페이지), 빠른 시작 지침 (8 페이지), 빠른 시작 매뉴얼 (7 페이지), 릴리스 노트 (5 페이지), 교체 지침 (4 페이지), 백서 (13 페이지), 기술 개요 (15 페이지), 빠른 사양 (17 페이지), 사양 (49 페이지), 시작하기 매뉴얼 (34 페이지), 설치 매뉴얼 (18 페이지), 분해 지침 매뉴얼 (9 페이지), 프로그래밍 매뉴얼 (8 페이지)

페이지 인쇄
HP StorageWorks 1000 - Modular Smart Array 설치
Comparison of multipathing options
Review the following feature comparison before proceeding, to
verify which multipathing option is best for your environment.
Table 1: Multipathing feature comparison
Basic
Feature
Windows
Supported
Windows
operating
system
Supported
Windows
number of
2000: 2
nodes in a
Widows
cluster
2003: 4
Maximum
2
supported
HBA per host
Maximum
2
supported
paths
Automatic
Yes
failover
Automatic
No
failback
Automatic
Yes
messaging to
the LCD panel
and event log
Graphical
No
User Interface
Support for
Yes
Selective
Storage
Presentation
Coexistence of
No
basic
multipathing
to EVA &
MSA devices
on same
server
Coexistence of
No
basic
multipathing
and Secure
Path on same
server
Coexistence of
No
basic
multipathing
and Secure
Path on
different
servers in the
same SAN
Basic
Advanced
Linux
Secure Path
Linux
Windows
Linux
NetWare
ServiceGuard
All supported
:16
configurations
LifeKeeper: 6
nodes
16
Windows: 8
Linux: 16
8
32
Yes
Yes
No
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
No
No
No
Enabling Windows basic failover
Basic Multipath Input Output (MPIO) failover capability is
supported in Microsoft Windows 2000 and Windows
Server 2003 (32-bit and 64-bit) operating system environments.
Note:
These instructions assume that installation of the SAN and the
MSA is complete. Refer to information shipped with the server,
switch, and MSA for installation and configuration information.
Clustered and non-clustered server environments must install these
multipathing components on each server with access to the MSA.
Components (and installation instructions) described in this section
are obtained from links provided in MSA web sites.
http://www.hp.com/go/msa1000
MSA1000 web site:
http://www.hp.com/go/msa1500cs
MSA1500 cs web site:
1. Verify that other multipathing software, such as Secure Path,
is not present on the system.
If other multipathing software is currently installed, do not
proceed with these instructions.
Either continue using your previous solution, or completely
uninstall that solution from your environment.
2. Verify that MSA controller firmware that supports basic
multipathing is installed on your MSA.
MSA1000:
4.32 or later
MSA1500 cs: 4.82 or later
To determine the current version of installed MSA firmware,
scroll through the messages on the controller LCD panel,
until the firmware version is displayed.
If an update is necessary, obtain and install new firmware
from the Software, Firmware & Drivers page of the MSA
web site.
3. Verify that the currently supported HBA firmware and driver
is installed on each server.
To determine the latest supported HBA firmware and driver
versions, refer to the MSA Compatibility Guide, available on
the MSA web site.
To determine the currently installed HBA firmware and driver
versions, either view the server monitor during the startup
process or view the SCSI and RAID Controllers information
in Device Manager.
If an update is necessary, obtain and install the HBA
components from the link on the Software, Firmware &
Drivers page of the MSA web site.
Note:
If using the STORport driver, obtain and install the latest
operating system patch from the Microsoft web site:
http://www.microsoft.com. Refer to KB article 838894.
4. Verify that only the primary path (connected to the I/O
module behind controller1) is connected between the server
and the MSA.
During the installation procedure of the next step, only one
path to the storage can be visible.
If necessary, disconnect the cables to the redundant path.
See other side