HP StorageWorks 1000 - Modular Smart Array 설치 - 페이지 4

{카테고리_이름} HP StorageWorks 1000 - Modular Smart Array에 대한 설치을 온라인으로 검색하거나 PDF를 다운로드하세요. HP StorageWorks 1000 - Modular Smart Array 4 페이지. Power supply, computer
HP StorageWorks 1000 - Modular Smart Array에 대해서도 마찬가지입니다: 네트워크 매뉴얼 (8 페이지), 지원 목록 (34 페이지), 오류 방지 매뉴얼 (12 페이지), 기술 백서 (12 페이지), 펌웨어 업데이트 (9 페이지), 개요 (20 페이지), 설치 매뉴얼 (2 페이지), 지원 전화번호 (19 페이지), 참조 매뉴얼 (48 페이지), 관리 매뉴얼 (40 페이지), 릴리스 노트 (13 페이지), 빠른 시작 지침 (8 페이지), 빠른 시작 매뉴얼 (7 페이지), 릴리스 노트 (5 페이지), 교체 지침 (4 페이지), 백서 (13 페이지), 기술 개요 (15 페이지), 빠른 사양 (17 페이지), 사양 (49 페이지), 시작하기 매뉴얼 (34 페이지), 설치 매뉴얼 (18 페이지), 분해 지침 매뉴얼 (9 페이지), 프로그래밍 매뉴얼 (8 페이지)

페이지 인쇄
HP StorageWorks 1000 - Modular Smart Array 설치
Device Manager status information
In the following example, three LUNs are being presented to the
server, but because there are two paths to the storage, the number
of listed SCSI Disk Devices is duplicated. With multipathing
support enabled, Device Manager also shows three Multi-Path
Disk Devices, one for each LUN.
This example also shows multipathing support enabled on the
HBAs.
Figure 2: Device Manager showing multipath support
Recovering from failover situations
For some failover events, sufficient information is provided in the
monitoring tools to assist the diagnosis and repair of the problem.
If information regarding the cause of the failover event is not
available, examine the following items in the failed path:
Cable connections of each device:
— Server
— HBA
— Switch
— MSA I/O module
HBA health
Switch health
MSA controller health
Schedule a system maintenace window as needed to reseat or
replace any faulty hardware.
Note:
When the MSA is restarted, controller1 (the primary, right
controller) is made the active controller. If a problem still exists on the
primary path, the system automatically fails over to the redundant
path.
Uninstalling Windows basic failover
1. Verify that only the primary path (connected to the I/O
module behind controller1) is connected between the server
and the MSA.
Only one path to the storage can be visible when uninstalling
MPIO.
If necessary, disconnect the cables to the redundant path.
2. From the server, select Start > Settings > Control Panel.
3. Select Add/Remove Programs.
4. Select HP Modular Smart Array Multi Path Software,
click Remove, and then follow any onscreen instructions.
5. Restart the server.
6. Repeat these steps on each server with access to the MSA.
Uninstalling Linux basic failover
To uninstall the components from the driver kit, use the
INSTALL script with the -u option:
# ./INSTALL -u
If you want to manually uninstall all the components, or you want
to uninstall just one of the components, use one or all of the
following commands:
# rpm -e fibreutils
# rpm -e hp_qla2x00
# rpm -e hp_qla2x00src