Olympus BH2-5RE 완전한 분해, 청소 및 재조립 - 페이지 3
{카테고리_이름} Olympus BH2-5RE에 대한 완전한 분해, 청소 및 재조립을 온라인으로 검색하거나 PDF를 다운로드하세요. Olympus BH2-5RE 18 페이지. Modular revolving nosepiece
페이지 인쇄
Sources for Replacement Parts, Tools, and Supplies Referenced in this Document ........................................................ 18
Table of Figures
Figure 1 - A typical JIS Screw .................................................................................................................................................. 5
Figure 2 - The BH2-5RE modular revolving nosepiece ........................................................................................................... 6
Figure 3 - Basic components of the BH2-5RE ......................................................................................................................... 6
Figure 4 - Remove four screws securing the dovetail slide .................................................................................................... 7
Figure 5 - Remove the loose dovetail slide ............................................................................................................................ 7
Figure 6 - Remove screws securing the cover in place .......................................................................................................... 7
Figure 7 - Remove the protective cover ................................................................................................................................. 7
Figure 8 - The turret assembly (without cover) ..................................................................................................................... 7
Figure 9 - Screwdriver modified to remove slotted lock ring ................................................................................................ 8
Figure 10 - Insert screwdriver into bores to lock turret ......................................................................................................... 8
Figure 11 - Loosen the slotted lock ring ................................................................................................................................. 8
Figure 12 - Remove the slotted lock ring ............................................................................................................................... 8
Figure 13 - Remove the pivot-adjustment screw ................................................................................................................... 9
Figure 14 - Remove the center-pivot bearing ball ................................................................................................................. 9
Figure 15 - Remove the screws securing the detent stop ...................................................................................................... 9
Figure 16 - Remove the loose mechanical detent stop .......................................................................................................... 9
Figure 17 - Remove the knurled-rubber grip ring .................................................................................................................. 9
Figure 18 - Components of the turret assembly .................................................................................................................. 10
Figure 19 - Loosen the threaded retaining ring ................................................................................................................... 10
Figure 20 - Remove the threaded retaining ring .................................................................................................................. 10
Figure 21 - Remove the perimeter bearing balls ................................................................................................................. 10
Figure 22 - Lift and remove the stationary base .................................................................................................................. 10
Figure 23 - Reinstall stationary base into revolving turret ................................................................................................... 11
Figure 24 - Apply ring of fresh grease for the bearing balls ................................................................................................. 11
Figure 25 - Place the bearing balls into the ring of grease ................................................................................................... 11
Figure 26 - Engage the threaded retaining ring ................................................................................................................... 11
Figure 27 - Tighten the threaded retaining ring ................................................................................................................... 11
Figure 28 - Remove any grease squeeze-out ....................................................................................................................... 12
Figure 29 - Apply grease to the center-pivot bore ............................................................................................................... 12
Figure 30 - Place bearing ball into the center-pivot bore .................................................................................................... 12
Figure 31 - Apply grease to the top of the bearing ball ....................................................................................................... 12
Figure 32 - Reinstall the pivot-adjustment screw ................................................................................................................ 12
Figure 33 - Reinstall the slotted lock ring ............................................................................................................................. 13
Figure 34 - Tighten the slotted lock ring .............................................................................................................................. 13
Figure 35 - Place the mechanical detent stop in position .................................................................................................... 13
Figure 36 - Secure the detent stop with two screws ........................................................................................................... 13
Figure 37 - Apply grease to the five detent notches ............................................................................................................ 14
Figure 38 - Place cover in position on the turret assembly .................................................................................................. 14
Figure 39 - Secure protective cover using three screws ...................................................................................................... 14
Figure 40 - Position dovetail slide onto stationary base ...................................................................................................... 14
Figure 41 - Secure dovetail slide onto stationary base ........................................................................................................ 14
Figure 42 - Apply black adhesive to revolving turret ........................................................................................................... 15
Figure 43 - Reinstall the knurled-rubber grip ring ................................................................................................................ 15
Figure 44 - Remove any adhesive squeeze-out .................................................................................................................... 15
Complete Teardown, Cleaning, and Reassembly of the Olympus BH2-5RE Modular Revolving Nosepiece
Page 3 of 18
Revision 3