Digiflex RF160 설치 관리자 참조 설명서 - 페이지 2

{카테고리_이름} Digiflex RF160에 대한 설치 관리자 참조 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Digiflex RF160 8 페이지. 2 channel smart rf wireless output module - 433mhz

페이지 인쇄

RF160 - 2CH SMART RF Output Module - 433MHz

The 2 Channel SMART RF Wireless Output Module, is

an advanced 433MHz RF transceiver with 2 indepen-

dently controllable relay outputs. Output functionality is

configured via panel programming, and any number of

RF outputs can be used, up to the maximum number of

outputs supported on the panel.

The panel must be fitted with one or more RF120 and/or

RF121 Smart RF Receivers (V2.51or higher).

The unit is compact so it can easily fit inside a gate

controller cabinet or can be mounted easily to most

surfaces. The wide operating voltage 9 to 28 volts AC/DC

makes it easy to power from third-party controllers or

power supplies.

The 2-Way communication protocol is encrypted with

rolling code and anti substitution technology making

the RF160 an ideal choice for controlling gates, garage

doors, lights or security systems.

Box Contents

The RF160 box contains the following parts.

2 Channel SMART RF Stand Alone Controller

1 x Antenna Instruction Sheet

Compatible Keyfobs

RF110 Smart 5 Button Keyfob

RF110FK - Colour Facia Kit One Of Each Colour

(Red, Blue, Green, Orange, Black, Grey, Yellow)

Figure 1: RF110 Smart 5 Button Keyfob

Mounting Considerations:

•

The receiver should be mounted in a location at

least 2 metres from other receivers.

Page

P/N: RF160IRG Rev 1.0



•

The receiver should be mounted on a vertical sur-

face with at least 30cm clearance from metal objects.

•

Avoid mounting the receiver in areas with significant

metal or electrical wiring.

•

Avoid mounting the receiver in areas where it may

be exposed to moisture or high humidity.

•

Reception distances are generally improved with

higher mounting locations and with no metal ob-

jects near the unit.

•

If range is not achievable due to environmental or

specification limitations then look at relocating the

unit to a more appropriate location.

Receiver Operation

The RF160 will turn on the green RX LED to indicate the

unit is powered and it will blink off each time a signal is

received. Each time a Keyfob button is pressed the corre-

sponding relay will operate and a confirmation signal is

sent to the Keyfob to indicate a successful 2 way transac-

tion. When button RLY1 or RLY2 are triggered manually

they operate the corresponding relay to allow you to

test your connections and device your operating.

WARNING always be sure to check that there is no ob-

jects in the way when operating an automatic device as

this could cause damage or injury to a person.

Relay Programming

Before configuring RF outputs, the control panel needs

to be communicating to an existing Digiflex smart RF

receiver (refer to both the control panel and smart RF

receiver installation manuals for further information).

You need to configure an output at the control panel

from the available event types provided - refer to the

control panel installation manual for further information.

Each relay on the RF160 can follow a single control panel

output when the event occurs.

Configuring Output At Control Panel - Example

The example below will configure an output to operate a

garage door controller (in this example using output 6).

MENU 4-1-0 Output Name < Garage Door >

MENU 4-1-1 Event Type < 60 = Door >

MENU 4-1-2 Event Assignment < 01 = Door 1 Name >

MENU 4-1-3 Output Polarity < 04 = Open, 1 Shot Low >

MENU 4-1-4 Output Time Parameter < 001 Second >

E&OE