Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 설치 참고 사항 - 페이지 42

{카테고리_이름} Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대한 설치 참고 사항을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 46 페이지. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대해서도 마찬가지입니다: 설치 참고 사항 (14 페이지), 솔루션 매뉴얼 (17 페이지), 백서 (19 페이지), 설명 (1 페이지), 제품 게시판 (6 페이지), 공지 사항 (4 페이지), 데이터시트 (9 페이지), 데이터시트 (18 페이지), 백서 (18 페이지), 구성 매뉴얼 (8 페이지), 설치 참고 사항 (28 페이지), 문제 해결 매뉴얼 (11 페이지), 설치 참고 사항 (18 페이지), 사용자 설명서 (17 페이지), 설치 참고 사항 (24 페이지), 매뉴얼 (19 페이지), 설치 참고 사항 (36 페이지)

페이지 인쇄
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 설치 참고 사항

Attaching Your ESD Grounding Strap

Figure 30
FAN
STATUS
Attaching Your ESD Grounding Strap
Electrostatic discharge (ESD) damage, which can occur when modules or other FRUs are improperly
handled, results in intermittent or complete failures. Modules consist of printed circuit boards that are
fixed in metal carriers. Electromagnetic interference (EMI) shielding and connectors are integral
components of the carrier. Although the metal carrier helps to protect the board from ESD, always use
an ESD grounding strap attached to a properly grounded bare metal surface when handling modules.
Follow these guidelines for preventing ESD damage:
•
•
Catalyst 6500 Series Distributed Forwarding Card 3 for WS-X67xx Modules Installation Note
42
Ejector Lever Closure in a Vertical Slot Chassis
All ejector levers flush
with module faceplate
Always use an ESD wrist strap and ensure that it makes maximum contact with bare skin. ESD
grounding straps are available with banana plugs, metal spring clips, or alligator clips. All
Catalyst 6500 series chassis are equipped with a banana plug connector (identified by the ground
symbol next to the connector) somewhere on the chassis front panel.
If you have an older Catalyst 6500 series chassis equipped with a plastic banana plug connector,
–
we recommend that you use either the supplied ESD grounding wrist strap (with a metal clip)
or an ESD grounding wrist strap equipped with an alligator clip.
If you have a newer Catalyst 6500 series chassis that has a bare metal hole as the banana plug
–
connector (also identified by the ground symbol next to the connector), we recommend that you
use a personal ESD grounding strap equipped with a banana plug.
If you choose to use the disposable ESD wrist strap supplied with the chassis or an ESD wrist strap
equipped with an alligator clip, you must attach the system ground lug to the chassis in order to
provide a proper grounding point for the ESD wrist strap.
78-15893-08