Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 설치 참고 사항 - 페이지 43

{카테고리_이름} Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대한 설치 참고 사항을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 46 페이지. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대해서도 마찬가지입니다: 설치 참고 사항 (14 페이지), 솔루션 매뉴얼 (17 페이지), 백서 (19 페이지), 설명 (1 페이지), 제품 게시판 (6 페이지), 공지 사항 (4 페이지), 데이터시트 (9 페이지), 데이터시트 (18 페이지), 백서 (18 페이지), 구성 매뉴얼 (8 페이지), 설치 참고 사항 (28 페이지), 문제 해결 매뉴얼 (11 페이지), 설치 참고 사항 (18 페이지), 사용자 설명서 (17 페이지), 설치 참고 사항 (24 페이지), 매뉴얼 (19 페이지), 설치 참고 사항 (36 페이지)

Note

•

If your chassis does not have the system ground attached, you must install the system ground lug.

Refer to the online Catalyst 6500 Series Switches Installation Guide for the procedure.

Note

After you install the system ground lug, follow these steps to correctly attach the ESD wrist strap:

Attach the ESD wrist strap to bare skin as follows:

Step 1

If you are using the ESD wrist strap supplied with the FRUs, open the wrist strap package and

unwrap the ESD wrist strap. Place the black conductive loop over your wrist and tighten the strap

so that it makes good contact with your bare skin.

If you are using an ESD wrist strap equipped with an alligator clip, open the package and remove

the ESD wrist strap. Locate the end of the wrist strap that attaches to your body and secure it to your

bare skin.

Grasp the spring or alligator clip on the ESD wrist strap and momentarily touch the clip to a bare metal

Step 2

spot (unpainted surface) on the rack. We recommend that you touch the clip to an unpainted rack rail so

that any built-up static charge is then safely dissipated to the entire rack.

Attach either the spring clip or the alligator clip to the ground lug screw as follows (See

Step 3

If you are using the ESD wrist strap that is supplied with the FRUs, squeeze the spring clip jaws

open, position the spring clip to one side of the system ground lug screw head, and slide the spring

clip over the lug screw head so that the spring clip jaws close behind the lug screw head.

Note

If you are using an ESD wrist strap that is equipped with an alligator clip, attach the alligator clip

directly over the head of the system ground lug screw or to the system ground lug barrel.

78-15893-08

This system ground is also referred to as the network equipment building system (NEBS)

ground.

You do not need to attach a supplemental system ground wire to the system ground lug; the

lug provides a direct path to the bare metal of the chassis.

The spring clip jaws do not open wide enough to fit directly over the head of the lug screw

or the lug barrel.

Catalyst 6500 Series Distributed Forwarding Card 3 for WS-X67xx Modules Installation Note

Attaching Your ESD Grounding Strap

Figure

31):