Sony BVP-900 Series 운영 매뉴얼 - 페이지 11

{카테고리_이름} Sony BVP-900 Series에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sony BVP-900 Series 48 페이지. Color video camera

페이지 인쇄

1 POWER indicator

Lights as follows to show the power-supply status.

Green: Power is supplied to the BVP-900/900P.

Red: The CAMERA POWER switch of the CCU-

700A/700AP is set to the off position, or the CAM

PW button of the MSU-700 or RCP-700-series unit

is set to off.

Yellow: Power is supplied to the BVP-900/900P,

however the VF PW button of the MSU-700 or

RCP-700-series unit is set to off and power is not

supplied to the viewfinder.

Not lit: Power is not supplied to the camera.

2 Video signal select buttons

Select the video signals (R, G, and B) displayed on the

viewfinder.

When the TEST OUT switch on the internal MS board

is set to VF, the TEST OUT connector outputs the

same signals as those displayed on the viewfinder.

• The R, G, and B buttons can be pressed together or

separately and the signals corresponding to the

pressed buttons are output. When two buttons are

pressed, the corresponding signals are mixed and

then output.

• When the R, G, and B buttons are pressed at the

same time, a Y signal is output to the viewfinder and

the TEST OUT connector.

• When no button is pressed, the following signals are

output:

When a black-and-white viewfinder is used: A Y

signal is output to the viewfinder and the TEST

OUT connector.

When a color viewfinder is used: The R, G and B

signals are output to the viewfinder, and a color

picture appears on the viewfinder. The TEST

OUT connector outputs a Y signal.

3 H-POSI (horizontal position) control

Adjusts the horizontal position of the box cursor on the

viewfinder screen.

4 V-POSI (vertical position) control

Adjusts the vertical position of the box cursor on the

viewfinder screen.

5 WIDTH control

Adjusts the width of the box cursor on the viewfinder

screen within the safety zone.

See description of the SAFETY ZONE switch.

6 HEIGHT control

Adjusts the height of the box cursor on the viewfinder

screen within the safety zone.

See description of the SAFETY ZONE switch.

7 RET (return video) button

Press this button when another return video system is

used, then the return video signal selected at the

RETURN SELECT knob can be monitored on the

viewfinder screen. When the TEST OUT switch on

the MS board is set to VF, the TEST OUT connector

also outputs the selected return video signal. If you

press this button again, the camera's video signal is

output to the viewfinder and the TEST OUT

connector.

8 RET 1 (return video 1) button

• Press to monitor the return video 1 signal on the

viewfinder screen. When the TEST OUT switch on

the MS board is set to VF, the TEST OUT connector

also outputs the return video 1 signal. If you press

this button again, the camera's signal is again output

to the viewfinder and the TEST OUT connector.

• When using the BVP-900/900P as a stand-alone

camera, the playback signal on a VTR is output.

Notes

• The RET 1 button has priority over the RET button if

both buttons are pressed. (The TEST OUT switch

setting has no effect on the priority.)

• When the TEST OUT switch is set to RET, the TEST

OUT connector outputs the return video signal

regardless of the setting of the video signal select

button.

9 RETURN SELECT knob

Selects a return video signal on the viewfinder screen

when the RET button is depressed.

!º Back tally lamp

Lights when a red tally signal is supplied. When the

CALL button on the MSU-700 or RCP-700-series unit

is pressed, the lamp lights if it is not lit, and goes out if

it is lit. You can adjust the brightness of the tally lamp

using the control on the internal AT board.

Attach the supplied number plate (0 through 9) to

show the camera number.

For details on adjusting the brightness and attaching a

number plate, refer to the System Manual.

9 (E)