ARGSeguridad ZDAS-300 사용자 설명서 - 페이지 8

{카테고리_이름} ARGSeguridad ZDAS-300에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. ARGSeguridad ZDAS-300 16 페이지. Luxury voiced lcd alarm system

페이지 인쇄

If no action has been performed on the keypad and the panel is in the DISARMED mode,

the panel LCD screen will show as following:

DIS

ARMED

LOG

Figure5 : LCD display when disarmed

: it means that the panel has been set to sounder alarm

: It means there are 85 items of information (including alarm information,

Armed / disarmed information and others).

: It means the date: November 8th.

: It means the time: 18:52

: It Means weekday Tuesday.

Timed

: It means timed auto arming/disarming has been programmed

: It means there are 2 items of alarms which have not been viewed. After

Viewing the information, the display 02 will disappear.

: It means that the No. 1 zone armed within 8 zones from No.1 to No.1 8

2.2.2 When the panel is set in the away armed mode,the LCD screen will show the following :

ARMED

LOG

Figure 6: LCD display when part armed

The meaning of the characters as follows:

83:Means there are 83 items of information (including alarm information, Armed/Disarmed

information and others).

1234 78 : Means that Zone No. 1, 2, 3, 4,7and 8 zones are armed.

Zones 5 & 6 are Un-Armed as there are no sensors in the two zones

2.2.3 When there is an alarm, the panel LCD will show as following:

TIMED

After entering correct PIN code the panel will follow the instructions given using the

DTMF tones from the keypad of the remote phone.

Press 1 to tell the panel to switch to listen in mode

Press 2 to tell the panel to switch to speak mode

Press 3 to tell the panel to switch its sounder ON

Press 4 to tell the panel to switch listening in OFF

Press 5 to tell the panel to terminate the call, disengage the phone line

Press 6 to tell the panel to switch its sounder OFF

Press 7 to tell the panel to ARM

Press 8 to tell the panel to DIS ARM

4.9 Listen in and speak through key fob

When the phone connected to the panel is call ed ,and the phone rings , press a single

key on the Key Fob directly , then the user could Listen in the premise and speak to the

occupants.

4.10 Alarm confirming

When the panel reports an alarm event to the C.S.it does so by using Ademco contact

Zone.

ID protocol, sometimes called ADEMCO fast format. After the data is transferred to the

C.S. the operator then has access to the customer details, address, name, phone numbers,

key holders etc. He also has audio access to the premises. He can Listen-in or Speak to the

occupants, this will allow the C.S. operator to request a pre-arranged password to confirm

the identity of the person he is speaking to or make a challenge to an unindented occupant.

The C.S. operator will take the appropriate action determined by the circumstances at the

time.

The C.S. Pry 1 and Pry 2 phone numbers are located in fields 1 and 2 and the account

code is located in field 7 in the PHONE program and configuration. In addition to above

procedure the panel has the ability to report alarm incidents to up to 4 private telephone

numbers. These dedicated numbers must be programmed into fields 3 to 6 of the PHONE

program and configuration. These numbers are referred to as USER numbers.

After reporting an alarm event to the C.S., once the C.S. has terminated the call the

panel Can be programmed to call the USER numbers in sequence, i.e No3 field First, then

4 etc.

When the panel dials the user phone number and the user answers the telephone,

there will be a beep sound from the panel showing that the phone is being answered. The

user then presses the * key on USER hand set to confirm the alarm, on doing so the panel

will allow the USER to listen-in the premises.