ARGSeguridad ZDAS-300 사용자 설명서 - 페이지 9

{카테고리_이름} ARGSeguridad ZDAS-300에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. ARGSeguridad ZDAS-300 16 페이지. Luxury voiced lcd alarm system

페이지 인쇄

4.5 Selectable key fob require assistance with/without sounder

How to set the function: Press 'Sensor ' key and - - - appears on the LCD. Press the disarm

key on the registered Key Fob or entering the preprogrammed PIN code, LCD will display

'DEL Sensor' Use Key pad to select Zone(s) 0, then select key fob number 1 to 9.Program the

character of the Key Fob with 0 or 1 to suit. Press Key Fob or ESC to save and exit. refer to

figure 25.

4.6 Omitting a Zone

It may be a requirement to temporarily omit a selected Zone or a number of Zones when

the system is armed. When a zone is selected to be omitted it will only be omitted for current

operation. When next time your System is armed, the omitted ZONE or ZONES will be

re-enstated into the system.

Note: The function is suitable for the armed zone or zones. But 24 hour zone can never

be omitted.

How to Omit a zone or zones: Press Arm button on the panel, then using the numeric

keypad on the panel press the number of the zone want to be omitted, then press the Disarm

key, enter the PIN code to complete the operation.

4.7 Sounder or Silent alarm setting:

How to set the function: Press the # key for 2 seconds when the panel is in disarmed mode,

the symbol of speaker displays or disappears; When it displays, the panel would alarm with

sounder ON, while when it disappears, the panel will alarm silently.

Note: Whether the key fob alarms with/without sounder subjects to its own configuration.

When the panel is set with silent alarm, the key fob will still be sounder alarm if it is set with

sounder alarm.

4.9 Access the Control Panel from a remote telephone (mobile or

land line)

The Remote Control enables the use of the land line phone or mobile phone to remotely

control panel. Call the phone number of the line connected to the alarm panel, the panel will

answer the call after 1 to 8 rings (programmable). When the panel answers the call enter the

pre-programmed 6 digit PIN code on the phone keypad to gain access to the Panel.

If the correct 6 digit PIN code is entered a long tone will be emitted from the panel. If the

PIN code is incorrect, three short tones will be emitted from the panel.You must try again and

enter the correct PIN code.

LOG

Figure7 : LCD display when alarmed

The figure shows that Zone 3 detector No2 has generated the Alarm signal at 6:10 on

, Oct.

3 INSTALLATION INFORMATION

3.1 The Basic Flow Chart for Registering Devices, Set Zone Type,

Set System Configuration and Program C.S. phone numbers and

Site Code in Disarmed mode.

1 To register Key fobs

2 To register Detectors

Press PROG key

3 To set Zone type

4 To set System configuration

5 To set C.S phone NO and account

Activate the key fob to be register CODE appears on LCD, comfirming the code has been received .

Press 0 to select key fob zone. Unit will auto register key fob with next reg. No , eg. If already 2 key

To register Key fobs

fobs registered, the new key fob will be allocated No 3.Press PROG to save the code. SENSOR

appears again to register more devices or press registered key fob to exit

Activate the detector to be registered CODE appears on LCD, confirming the code has been received

Press 1--8 to select the zone you wish the detector to be allocated to. Unit will auto register the de-

To register Sensors

tector with next reg. No, eg, if already 3 detectors registered, the new detector will be allocated No 4.

Press PROG to save the code. SENSOR appears again to register more devices or press registered key

fob to exit

Press * key ,LCD will display ZONE TYPE, press 1---8 to select zone, select 1 or 0 for all 7 fields

To set zone type

per zone. Press PROG to save. Press * key, LCD will display ZONE TYPE to reset the other ZONE

TYPE or press registered key fob to exit

To set system config

Press # key, LCD will display SYS CONFIG, press 00 to 17 to select the configuration of the system.

Press PROG to save. Press # key, LCD will display SYS CONFIG to re_configure the system or press

registered key fob to exit

Press * key, then press # key, the LCD will display PHONE , press 1 and display current C.S. Pry 1

phone No, enter new Pry 1 phone No, press PROG to save the phone, press * key then # key, the LCD

To set C.S phone number

will display PHONE, press 2 and display current C.S. Pry 2 phone No, enter new Pry 2 phone No,

press PROG to save, using this way, can set C.S. Account in Pry 7. or other private phone No, press

the registered key fob to exit

ALM

Press registered remote

SENSOR appears on LCD

key fob or enter your PIN

ready to register key fob or detectors