Epson 7850p - PowerLite XGA LCD Projector 제품 정보 매뉴얼 - 페이지 19

{카테고리_이름} Epson 7850p - PowerLite XGA LCD Projector에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 7850p - PowerLite XGA LCD Projector 25 페이지. Release of check tool for network projectors v1.00 for windows
Epson 7850p - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 사용자 설명서 (12 페이지), 교체 부품 (1 페이지), 운영 매뉴얼 (47 페이지), 제품 지원 게시판 (30 페이지), 설치 매뉴얼 (5 페이지), 빠른 설정 (2 페이지), 브로셔 및 사양 (2 페이지), 기술 요약 (7 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (42 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

페이지 인쇄
Epson 7850p - PowerLite XGA LCD Projector 제품 정보 매뉴얼
EPSON PowerLite 7850p Projector
If you're using a network management utility running SNMP,
you can configure your network to send trap alerts even without a
plug-n. See the User's Guide for more information.
Make sure you have installed the EMP Monitor software
(included on the projector's CD-ROM) on the computer you
want to use to monitor your projectors. (See the User's Guide
for instructions.)
Note: Your computer must be running Microsoft Windows XP,
2000, Me or 98.
Setting Up the Projector on a Wired Network
This section explains how to configure projectors on a wired
network. You can also configure projectors for wireless
communication. See "Configuring the Connection" on
page 12 for details.
1. Insert the PCMCIA LAN card into the card slot on the
back of the projector. Then connect the projector to your
network using a commercially available 100baseTX or
10baseT network cable.
2. Turn on the projector.
3. Press the
button on the remote control and select
Menu
from the
Network
Advanced2
Video
Video
Brightness Control
Brightness Control
Audio
Audio
Projector ID
Projector ID
Effect
Effect
Network
Network
Setting
Setting
COM Port
COM Port
User's Logo
User's Logo
Auto setup
Auto setup
Advanced1
Advanced1
BNC Sync Termination
BNC Sync Termination
Advanced2
Advanced2
Reset
Reset
About
About
Reset All
Reset All
[
[
]: Select
]: Select
[
[
]: Enter
]: Enter
4. If your network assigns addresses automatically, turn on
.
DHCP
If your network does not assign addresses automatically,
turn off
and enter the projector's
DHCP
,
Subnet Mask
Gateway Address
needed.
❏ To enter numbers using the remote control, press the
button until it lights, then use the numeric
Num
keypad.
Num button
18
EPSON PowerLite 7850p Projector
-
menu.
:
High
High
Low
Low
: 1
: 1
Set
Set
Select
Set
Set
:
RS-232C
RS-232C
USB
USB
Network
:
ON OFF
ON
OFF
:
ON
ON OFF
OFF
Execute
Execute
[Menu]: Exit
[Menu]: Exit
,
IP Address
, and
MAC Address
Zero
❏ To change the network addresses from the projector's
control panel, press the right and left arrow buttons to
select the part of the address you want to enter, then
use the up and down arrow buttons to increase or
decrease the numeric value.
Select the part of the
address to change
5. When you finish changing an address in the network menu,
press the
Enter
Auto/Enter
value.
6. When you're done making all necessary changes, press
to exit the menu system.
Opening and Closing EMP Monitor
To start EMP Monitor, click
Programs > EPSON Projector > EMP Monitor
If you've added the program to the Startup programs folder, it
may already be open. If so, click the icon in the system tray on
the lower-right corner of your screen to display the EMP
Monitor window:
To close EMP Monitor, right-click the program icon shown
above, then select
, as
6/03
button (on the remote control) or the
button (on the projector). This stores the
Start > Programs or All
Click here to start EMP Monitor
.
Exit
Increase or
decrease
the value
ESC
.