3Com OfficeConnect WX1200 빠른 시작 매뉴얼 - 페이지 7
{카테고리_이름} 3Com OfficeConnect WX1200에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 3Com OfficeConnect WX1200 10 페이지. Secure converged networks enterprise edition
3Com OfficeConnect WX1200에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (10 페이지), 빠른 시작 매뉴얼 (2 페이지), 데이터시트 (6 페이지), 제품 설명서 (15 페이지)
페이지 인쇄
Using the quickstart Command (any model)
To run the quickstart command:
Attach a PC to the WX switch serial console port. (Use
1
these modem settings: 9600 bps, 8 bits, 1 stop, no
parity, hardware flow control disabled.)
Press Enter three times to display a username prompt
2
(Username:), a password prompt (Password:), and
then a command prompt such as the following:
WX1200-aabbcc>
(Each switch has a unique system name that contains
the model number and the last half of the switch's
MAC address.)
Access the enabled level (the configuration level) of
3
the CLI:
WX1200-aabbcc> enable
Press Enter at the Enter password prompt.
4
Type quickstart. The command asks you a series of
5
questions. You can type ? for more help. To quit,
press Ctrl+C.
WX1200-aabbcc# quickstart
This will erase any existing config. Continue? [n]: y
Answer the following questions. Enter '?' for
help. ^C to break out
System Name [WX1200]: WX1200-Corp
Country Code [US]: US
System IP address []: 172.16.0.21
System IP address netmask []: 255.255.255.0
Default route []: 172.16.0.20
Do you need to use 802.1Q tagged default VLAN
[Y/N]? Y: y
Specify the port number that needs to be tagged
[1-2, <CR> ends config]: 2
Using the quickstart Command (any model)
Specify the tagged value for port [2] [<CR> ends
config:] 100
Specify the port number that needs to be tagged
[1-2, <CR> ends config]:
Admin username [admin]: wxadmin
Admin password [optional]: letmein
Enable password [optional]: enable
Do you wish to set the time? [y]: y
Enter the date (dd/mm/yy) []: 08/01/07
Is daylight saving time (DST) in effect [n]: n
Enter the time (hh:mm:ss) []: 18:58:00
Enter the timezone []: PST
Enter the offset from GMT for 'PST' in hh:mm [0:0]:
-8:0
Do you wish to configure wireless? [y]: y
Enter a clear SSID to use: public
Do you want Web Portal authentication? [y] y
Enter a username with which to do Web Portal,
<cr> to exit: user1
Enter a password for user1: user1pass
Enter a username with which to do Web Portal,
<cr> to exit:
Do you want to do 802.1x and PEAP-MSCHAPv2? [y]: y
Enter a crypto SSID to use: corporate
Enter a username with which to do PEAP-MSCHAPv2,
<cr> to exit: bob
Enter a password for bob: bobpass
Enter a username with which to do PEAP-MSCHAPv2,
<cr> to exit:
Do you wish to configure access points? [y]: y
Enter a port number [1-2] on which an AP
resides, <cr> to exit: 2
Enter AP model on port 2: ap3750
Enter a port number [1-2] on which an AP
resides, <cr> to exit:
Do you wish to configure distributed access
points? [y]: y
Enter a DAP serial number, <cr> to exit:
0422700351
Enter model of DAP with S/N 0422700351: ap3750
7