ClipperCreek HCS SERIES 설치 매뉴얼
{카테고리_이름} ClipperCreek HCS SERIES에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ClipperCreek HCS SERIES 9 페이지. Quad-mount kit.
innovative infrastructure for
electric and hybrid vehicles
ClipperCreek HCS SERIES에 대해서도 마찬가지입니다: 설치 매뉴얼 (20 페이지)
페이지 인쇄HCS SERIES EVSE PEDESTAL
INSTALLATION GUIDE
Please Note
This installation guide includes the latest information at the
time of printing. ClipperCreek, Inc. reserves the right to
make changes to this product without further notice.
Changes or modifications to this product by other than an
authorized service facility may void the product warranty.
Before You Begin:
Read these instructions completely, including the Safety
Instructions. If you have questions about the use of this
product, contact your Service Representative.
Note to the Installer:
Be sure to leave these instructions with the user.
Note to the User:
Keep these instructions for further reference.
Important Safety Instructions
ClipperCreek Electric Vehicle Supply Equipment (EVSE
or "charger") is designed with the safety concerns of the
end user as an utmost priority; however, the following
safety precautions must be read and followed:
The charger and electrical wiring should be installed
•
by a qualified electrician in accordance with local
electrical codes and ordinances.
Grounding Instructions - The charger should be
•
connected to a grounded, metal, permanent wiring
system; or an equipment-grounding conductor should
be run with circuit conductors and connected to a
grounding
terminal
Connections to the charger should comply with all
local electrical codes and ordinances.
Call your local service provider anytime a procedural
•
question arises; DO NOT attempt to perform a
procedure you are unsure of.
Read all installation instructions carefully before
•
performing the pedestal and charger installation.
_________________________
Notes:
_____________________________
_____________________________
_____________________________
_____________________________
_____________________________
_____________________________
_____________________________
_____________________________
_____________________________
or
lead
on
the
charger.
Installation Requirements
Required Equipment for a Single-Mount Pedestal with
one HCS Charging Station (One EVSE per Pedestal):
One (1) ClipperCreek HCS EVSE Pedestal Kit.
•
One (1) ClipperCreek HCS Charging Station (EVSE).
•
One (1) dedicated 208 or 240 VAC branch circuit.
•
One (1) circuit breaker appropriately sized for the
•
EVSE charging capacity.
Two (2) Live Line conductors with enough length to
•
comfortably pull all the way through and above the top
of the pedestal.
One (1) Ground Line conductor with enough length to
•
comfortably pull all the way through and above the top
of the pedestal.
Conduit sized to fit all three conductors.
•
Four (4) Anchor Bolts with Nuts and Washers
•
Required Equipment for a Dual-Mount Pedestal with
two HCS Charging Stations (Two EVSEs per Pedestal):
One (1) ClipperCreek HCS EVSE Pedestal Kit.
•
One (1) ClipperCreek Dual-Mount HCS Pedestal Kit.
•
Two (2) ClipperCreek HCS Charging Stations (EVSEs).
•
Two (2) dedicated 208 or 240 VAC branch circuits.
•
Two (2) circuit breakers, appropriately sized with
•
respect to the charging capacity of each EVSE.
Two pairs (2x2) Live Line conductors (one pair for each
•
EVSE) with enough length to comfortably pull all the
way through and above the top of the pedestal.
Two (2) Ground Line conductors (One for each
•
EVSE) or a single bonded Ground Line with
enough length to comfortably pull all the way
through and above the top of the pedestal.
Conduit sized to fit all Live Line and Ground Line
•
conductors.
Four (4) Anchor Bolts with Nuts and Washers
•
1
Refer to the EVSE documentation to determine the
appropriate circuit breaker current capacity.
2
All conductors must be appropriately sized for the
EVSE current capacity, in accordance with local and
NEC electrical codes.
Tools Required for Assembling the Pedestal
The following tools are required for the installation and
assembly of the pedestal components.
L-shape T27 Torx Driver (there are some tight spaces,
•
advise using both the long and short T27's for faster
assembly)
#2 Phillips Head Screwdriver
•
5/16" Flathead Screwdriver (for Ground Block Lug)
•
Box Wrench (appropriately sized for the Anchor Nuts)
•
Page 1 of 9
1
2
2
2
1
2