ClipperCreek HCS SERIES 설치 매뉴얼 - 페이지 4
{카테고리_이름} ClipperCreek HCS SERIES에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ClipperCreek HCS SERIES 9 페이지. Quad-mount kit.
innovative infrastructure for
electric and hybrid vehicles
ClipperCreek HCS SERIES에 대해서도 마찬가지입니다: 설치 매뉴얼 (20 페이지)
페이지 인쇄1. Concrete Pad Requirements
The location, dimensions, and composition of the concrete
pad underlying the pedestal should always adhere to local
building codes. The following dimensions are minimum
recommended values. Always verify that installation plans
adhere to local code requirements prior to proceeding.
The pad area must be a minimum of 18" to a side.
•
The concrete must be poured a minimum depth of 18".
•
If there is no bumper block, the center of the pedestal
•
base should be situated 36" behind the curb.
If a bumper block is in place, the center of the pedestal
•
base should be situated 12" behind the curb.
Figure 4: Proper Distance to the Curb
2. Anchor Bolt Placement
A minimum of four (4) anchor bolts must be embedded in
the concrete pad for the purposes of securing the pedestal
post. The pedestal base is designed to permit the anchor
bolts to be arranged in many configurations, including
the following:
For the Standard 10" Square Pattern:
Arrange four (4) 1/2" or 3/8" anchor bolts in a 10"
•
square pattern. This placement corresponds to the
corner cutouts in the pedestal base.
For the Alternate 5.25" x 11.1" Rectangular Pattern:
Arrange four (4) 3/8" anchor bolts in a 5.25" by 11.1"
•
rectangular pattern. This placement corresponds to the
short inner cutouts in the pedestal base.
HCS Series EVSE Pedestal Installation Guide
For the Alternate 10" x 4.75" Rectangular Pattern:
Arrange four (4) 1/2" anchor bolts in a 10" by 4.75"
•
rectangular pattern. This placement corresponds to fall
within the long inner cutouts in the pedestal base.
Maximum Anchor Bolt Height:
The anchor bolts should not protrude more than 3"
•
above the surface of the concrete pad.
Use the Pedestal Base Pattern Template:
To better facilitate the installation of the anchor bolts, a
cardboard template in the shape of the pedestal base is
included in the pedestal kit. This template is provided as a
knock-out piece on the back of the cardboard box in which
the cover plate is packaged. The template is specific for
two bolt patterns: the standard 10" x 10" pattern and an
alternate 5.25" x 11.1" rectangular pattern.
3. Mounting the Pedestal Post
Once the concrete pad with anchor bolts has been prepared
and the three service conductors have been pulled through
the underground conduit, the pedestal post may be placed.
Note: DO NOT remove the tape at the bottom of the
pedestal. This tape is provided for finish and weather
protection of the pedestal post.
Feed the three service conductors up through the
•
inside of the pedestal post. The conductors must be of
sufficient length to pass beyond the top of the pedestal
so that final connections can be worked with
comfortably at a later step.
Align the pedestal post base notches with the four
•
anchor bolts and ease it into place.
Nuts and washers may be used under the pedestal base
•
to adjust the vertical alignment of the pedestal should
the concrete pad not be level.
Secure the pedestal post base to the concrete anchor
•
bolts using appropriately sized nuts and washers.
The anchor bolts, nuts and washers used for the
•
installation of the pedestal base are not included in the
pedestal kit and must be purchased separately.
Page 4 of 9
Figure 5: Bolt Pattern Template Knockout