Auber Instruments SYL-3615 Instruction Manual - Page 2

Browse online or download pdf Instruction Manual for Controller Auber Instruments SYL-3615. Auber Instruments SYL-3615 7 pages. Wi-fi bbq controller
Also for Auber Instruments SYL-3615: Instruction Manual (5 pages)

Auber Instruments SYL-3615 Instruction Manual
AUBER INSTRUMENTS
Pit: -H-
Food: -H-
Figure 3(b). The display screen in normal operating mode.
2.2 Connecting Probes
Connect the pit probe to the P1 port, the food probe to the P2 port, and
the third probe to the P3 port. The screen should display the readings
from each probe in the designated areas, as shown in Figure 3 below.
Pit probe reading
Pit: 78
Food probe reading
Food: 77
Figure 4. A SYL-3615 shows readings from all three probe and the
set-temperature.
2.3 Plugging in the Fan
Connect the barrel connector from the fan (2.5 mm x 5.5 mm) to the
second port from the left, marked as FAN (refer to Figure 2).
3. Getting Familiar with Different Display Modes
From the normal operating mode, users can access other display modes to
check the status, switch to time-checking mode, edit the cooking profile, or
change settings. The diagram below illustrates how to switch to these display
modes.
Cooking Profile
Normal Operating Mode
>P-Status: Step-1
Pit: 78
SET
Step: 1
Pit: 225
Food: 77
SET
Hold for 2
Menu
seconds
>Control Setting
System Config
Figure 5. Switching to different display modes.
a)
Time-Checking Mode
Press the TIMER/BACK key to check the current step number,
step time, and the ending-criteria. Press the TIMER key one more
time to check the total cooking time and the output percentage to
the fan. Press the TIMER key again to return to the normal display
mode.
b)
Cooking Profile Mode
Press the SET key briefly to enter the Cooking Profile Setting Mode.
2024.01
Set: 225
P3: -H-
Set: 225
Set temperature
Probe 3 reading
P3: 77
Time-checking
Page 1
◀/
Set: 225
Step 2 Run 0:05
P3: 77
Ends at Temp 0
◀/
◀/
Page 2
Total Run 10:05
Power Output 100
c)
Menu Mode
Press and hold down the SET key for 2 seconds to bring up the
menu: Control Setting and System Configuration.
4. Pairing a SYL-3615 to a Wi-Fi Router
Important: The Wi-Fi module in SYL-3615 can only connect to a 2.4 GHz
Wi-Fi network. Please make sure your router broadcast 2.4 GHz Wi-Fi
frequencies.
4.1 Download and Install the Latest AuberWiFi app
Please download and install the latest AuberWiFi app from the app
store. Do NOT use the other app AuberSmart app for this device.
4.2 Set the Controller to Access Point (AP) Mode
The device can only be paired with your home router when it is in pairing
mode, or Access Point (AP) mode. When you receive a new SYL-3615
from Auberins.com, the unit should be in the Wi-Fi pairing mode,
indicated by the blue LED blinking rapidly.
To manually change the device to Wi-Fi pairing mode, press and hold
the SET key for 2 seconds to bring up the menu. Navigate to the
"System Config" sub-menu, scroll down to find "Reset WiFi", and select
"Yes". The device will restart and reset to AP mode.
4.3 Pair a SYL-3615 to a Wireless Router
a)
Before opening the AuberWiFi app, please ensure that your
phone is connected to a 2.4 GHz Wi-Fi signal from your
router.
Note: This step is important because our app need to acquire
the Wi-Fi name (SSID) and then send it to the SYL-3615 in a
later step.
b)
Open the AuberWiFi app, tap the "add a device" button.
c)
On the next page, your home WiFi's name (SSID) should
appear on the top line. Enter the Wi-Fi password and tap the
"Connect Device" button.
Note: You can tap the eye icon to check if the password is
entered correctly.
d)
Please read the pop-up message boxes and tap "CONTINUE"
and the app will take you to the Wi-Fi Setting page of your
phone.
e)
On a list of the available Wi-Fi signals, find the one starts with
"AuberWiFi_" and followed by 12 numbers and letters. This
Wi-Fi signal is generated by the SYL-3615 for pairing purpose
and it doesn't provide internet connection. No password is
needed.
WWW.AUBERINS.COM
P2/7