Jamr Technology B02T User Manual - Page 8
Browse online or download pdf User Manual for Blood Pressure Monitor Jamr Technology B02T. Jamr Technology B02T 17 pages.
Print Page5. Measurement Procedure
Note:
You should always be seated and calm before and during measurement.
5.1. Before measurement:
$YRLG HDWLQJ DQG VPRNLQJ DV ZHOO DV DOO IRUPV RI H[HUWLRQ GLUHFWO\ EHIRUH
measurement. These factors influence the measurement result. Find time to
relax by sitting in an armchair in a quiet atmosphere for about ten minutes
before taking a measurement.
5HPRYH DQ\ JDUPHQW WKDW ILWV FORVHO\ WR \RXU XSSHU DUP
$OZD\V PHDVXUH RQ WKH VDPH DUP QRUPDOO\ OHIW
$OZD\V FRPSDUH PHDVXUHPHQWV WDNHQ DW WKH VDPH WLPH RI GD\ VLQFH EORRG
pressure changes during the course of the day, as much as 20-40 mmHg.
5.2. Common sources of error:
Note: Comparable blood pressure measurements always require the same
conditions!
&RQGLWLRQV VKRXOG DOZD\V EH TXLHW
$OO HIIRUWV E\ WKH XVHU WR VXSSRUW WKH DUP FDQ LQFUHDVH EORRG SUHVVXUH 0DNH
sure you are in a comfortable, relaxed position and do not flex any of the
muscles in the measurement arm during the measurement. Use a cushion for
support if necessary.
,I WKH DUP DUWHU\ OLHV FRQVLGHUDEO\ ORZHU RU KLJKHU WKDQ WKH KHDUW DQ
erroneously high or low blood pressure will be measured! Each 25-30cm
difference in height between your heart and the cuff results in a measurement
error of 10 mmHg!
&XIIV WKDW DUH WRR QDUURZ RU WRR VKRUW UHVXOW LQ IDOVH PHDVXUHPHQW YDOXHV
Selecting the correct cuff is extremely important. Cuff size is dependent upon
the circumference of the arm (measured in the center). The permissible range
is printed on the cuff.
Cuff works Under the pressure range 0-300MMHG
The wide range rigid cuff is : 8.7" – 15.7" (22 - 40 cm)
Note: Only use approved cuffs!
$ ORRVH FXII RU D VLGHZD\V SURWUXGLQJ DLU SRFNHW FDXVHV IDOVH PHDVXUHPHQW
values.
:LWK UHSHDWHG PHDVXUHPHQWV EORRG DFFXPXODWHV LQ WKH DUP ZKLFK FDQ OHDG
to false results. Consecutive blood pressure measurements should be
repeated after a 1 minute pause or after your arm has been held up in order to
allow the accumulated blood to flow away. If you decide to take your Averaging
Mode measurement again, be sure to wait at least one minute beforehand.
5.3. Fitting the Cuff
Please refer to picture-06
a) The cuff is preformed for easier use. Remove tight or bulky clothing from
your upper arm.
b) Wrap the cuff around your upper left arm. The rubber tube should be on
the inside of your arm extending downward to your hand. Make certain the
cuff lies approximately 1/2" to 3/4" (2 to 3 cm) above the elbow. Important!
The
on the edge of the cuff (Artery Mark) must lie over the artery which
runs down the inner side of the arm.
c) To secure the cuff, wrap it around your arm and press the hook and loop
closure together.
d) There should be little free space between your arm and the cuff. You
should be able to fit 2 fingers between your arm and the cuff. Cuffs that don't
fit properly result in false measurement values. Measure your arm
circumference if you are not sure of proper fit.
e) Lay your arm on a table (palm upward) so the cuff is at the same height as
your heart. Make sure the tube is not kinked.
f)Remain seated quietly for at least two minutes before you begin the
measurement.
Picture-06