Alutech LM-LB Operating Manual - Page 2

Browse online or download pdf Operating Manual for Accessories Alutech LM-LB. Alutech LM-LB 2 pages. Photocells

Print Page

Operating

manual

PHOTOCELLS

LM-LB

ENGLISH

DESCRIPTION

The photocells are designed to warn of any foreign objects on the optical

axis between the transmitter (TX) and the receiver (RX) of the photocells.

DELIVERY SCOPE

Transmitter (TX) ......................................................................................................................1 pc.

Receiver (RX) ............................................................................................................................1 pc.

Manual .........................................................................................................................................1 pc.

Dowel with screw.................................................................................................................. 8 ps.

TECHNICAL SPECIFICATIONS

Transmitter (TX) supply voltage ........................... Lithium FR6 AA 1.5 V (2 pcs.)

Receiver (RX) supply voltage ................................................................ 12 V ... 24 V DC

Transmitter (TX) consumption .......................................................................... ≤ 0.5 mА

Receiver (RX) consumption .................................................................................. ≤ 40 mА

Range ............................................................................................................ no less than 12 m

Positioning accuracy ........................................................................................................... ± 5 °

Output relay contacts load ............................................................... 1 А / max 30 V DC

Output contacts type ........................................................................................ NC and NO

Infrared wave length .................................................................................................. 940 nm

Housing protection class ............................................................................................... IP 54

Working temperature range ................................................................... − 20 ... + 60 º С

Dimensions ................................................................................................. 100 × 55 × 31 mm

Connection cable cross-section .................................... max 1 mm2 (AWG16-26)

Display ...................................................................................................... LED on the receiver

(lit when photocells activated)

The Company reserves the right to make changes to this manual

and the technical specifications of the product without prior notice.

The content of this manual cannot serve the basis for legal claims.

СХЕМЫ УСТАНОВКИ И ПОДКЛЮЧЕНИЯ

СХЕМИ ВСТАНОВЛЕННЯ ТА ПІДКЛЮЧЕННЯ

INSTALLATION AND CONNECTION DIAGRAMS

Transmitter TX

Receiver RX

12 V/24 V

POWER

P O W ER

O N / O F F

P O W ER

Импортер в Республике Беларусь /

Уполномоченный представитель изготовителя:

ООО «Алютех Воротные Системы»,

Республика Беларусь, 220075, Минская обл.,

Минский р-н, СЭЗ «Минск», ул.Селицкого, 10,

тел. +375 (17) 330 11 00, +375 (17) 330 11 01

Імпортер в Республіці Білорусь /

Уповноважений представник виробника:

ТОВ «Алютех Воротні Системи»,

Республіка Білорусь, 220075, Мінска обл.,

Мінський р-н, СЕЗ «Мінськ», вул.Селіцкого, 10,

тел. +375 (17) 330 11 00, +375 (17) 330 11 01

Importer to the Republic of Belarus / Authorised representative:

Alutech Systems s.r.o.,

348 02, Czech Republic, Bor u Tachova, CTPark Bor,

Nova Hospoda 19, D5-EXIT 128,

phone / fax: + 420 374 6340 01,

e-mail: [email protected]

INSTALLATION AND CONNECTION

Only qualified specialists can install and connect the product in com

pliance with the regulatory documentation in force and following

the applicable safety procedures.

Before making any connections, check that the automation to which

the photocells are connected is disconnected from the mains and

from the batteries in case of accidental activation.

Before mounting the photocells select the location for the transmitter

and receiver, place them on one level at height of no more than 20

cm, and ensure that they are facing one another in a direct line. The

distance between transmitter and receiver should not exceed 50 cm.

Check that the selected mounting places are protected from impacts

and the mounting surfaces are strong enough. Lay the cables to the

transmitter and receiver mounting places beforehand.

When mounting, fasten the transmitter first and carry out electric con-

nections (see diagram), then align (center) the receiver. The photocells

are connected and aligned correctly if the receiver LED illuminates

when the optical ray is crossed and the relay switch sound is heard.

Check the photocells operation several times, then fasten the receiver,

finish the electric connections and assembling.

In this type of the photocells two batteries Lithium FR6 AA 1.5 V are

used for transmitter power supply. In the receiver there is an ALARM

OF BATTERY DISCHARGE (see diagram) which can be turned on and

off. The sound alarm is activated when the operation power supply be-

comes less than 2.3 V ± 0.1 V. In the transmitter there is a POWER ON /

OFF switch (see diagram).

There is an EDGE slot in the transmitter for connecting the safety de-

vices. If the safety devices are not used, an 8.2 kilohm resistor should

be installed into the EDGE slot (see diagram).

Due to the possible reflection of infrared rays from the floor, walls,

objects, etc. the photocells should be checked and used only with

the covers installed. The covers serve as filters for cutting the visible

light and contain rayfocusing lenses. Protect the photocell receiver

from direct sunlight.

Перед началом монтажа фотоэлементов, необходимо их разобрать, а затем монтировать в следующем порядке:

Перед початком монтажу фотоелементів, необхідно їх разібрати, а потім монтувати в наступному порядку:

Before mounting the photocells should be disassembled and then assembled in the following way:

1. Установить основание

Receiver RX

Встановити підставу

Fit the base

AlARM OF

BATTERY

DISCHARGE

OFF

EEP

LED

12 V/24 V

COM

P O W ER

O U TP U T

Рис. / Мал. / Fig. 1

2. Прикрутить среднюю часть фотоэлемента

Прикрутити середню частину фотоелемента

Screw the middle part of the photocell

If several pairs of photocells are to be installed in one line, receivers

should be placed at the edges and transmitters should be installed

in the center backtoback.

The installation and connection diagrams are shown on fig. 1–5.

STORAGE, TRANSPORTATION

AND DISPOSAL

Keep the packed product in dry premises at temperatures between

0...+25 °С and relative air humidity of no more than 80%. The air inside

must not contain acidic, alkaline and other deleterious substances. Do

not expose the product to precipitation and direct sunlight. Storage pe-

riod is two years from the date of manufacturing. Transportation may be

carried out by any roofed land vehicle fitted with load retention equip-

ment and other means preventing damage of the packages.

Disposal is to be performed in accordance with the current

waste processing and disposal regulations applicable in

the country of the Customer. The product does not con-

tain precious metals and substances that pose a threat to

life, human health or the environment. Operation life is five

years.

WARRANTY

The warranty on the operation capacity of the product is provided if

storage, transportation and maintenance are carried out according to the

set regulations. Warranty period is three years. Within the warranty period,

the service department providing warranty maintenance eliminates mal-

functions caused by the fault of the Manufacturer.

Note: the parts replaced under the warranty are considered the property of the

service department that carried out the product repair.

The warranty does not apply in the following cases:

•

violation of use and storage regulations;

•

alterations performed by unauthorised persons, damage to the

product caused by the Customer or third parties;

•

damage caused by water ingression within the device;

•

force majeure (fires, lightning strikes, floods, earthquakes and other

natural disasters);

•

failure to provide a complete operation manual.

For information about service providers go to:

http://www.alutech-group.com/feedback/service/.

STATEMENT OF COMPLIANCE

Copies of declarations of compliance can be found at:

http://www.alutech-group.com/product/other/auto/DOCUMENTS/

Made in China

Manufacturer: 'Hangzhou Hiland Technology Co., Ltd' ,

building, 2Xiyuanwu road, Westlake Technology garden,

Hangzhou, China +86 571 81958376

3. Подключить провода и прикрутить плату

Підключити дроти і прикрутити плату

Connect wires and screw the board

Рис. / Мал. / Fig. 2

4. Закрыть светофильтром

Закрити світлофільтром

Cover with the light filter

Рис. / Мал. / Fig. 3

Рис. / Мал. / Fig. 4

Рис. / Мал. / Fig. 5

09.2019