Boumatic Opti-Flo II Handleiding voor installatie-instructies - Pagina 2

Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} Boumatic Opti-Flo II. Boumatic Opti-Flo II 13 pagina's. Upgrade kit

Pagina afdrukken

Installation

1. Disconnect power from the electrical supply.

2. Open the Opti-Flo II enclosure.

3. Remove the plastic cover of the ABB ACS 300 control

by loosening the 2 screws at the bottom of the cover

and squeezing the 2 plastic tabs located at the topside

of the cover.

— NOTE ————————————————––––––––––––

Do not cut the wires going to the ABB ACS 300 control.

4. Remove ONLY the wires from the terminal blocks of

the ABB ACS 300 control.

5. Remove the solid color brown, red and orange wires

from the Opti-Flo II main terminal block which come

from the input filter. Discard the filter.

6. Take the ABB ACS 300 control out of the enclosure

by removing and saving the 4 mounting screws and

locking washers.

— WARNING ——————————————————–

Before opening control box disconnect power from electrical

supply or severe injury or death could occur.

— WARNING ——————————————————–

Dangerous voltage. Consult Magnetek users manual before

opening the Magnetek controller. Wait at least 5 minutes after

disconnecting supply before removing the cover. High leakage

current. Earth connection essential before connecting supply.

7. Install the Magnetek GPD 315 assembly into the Opti-

Flo II enclosure using the 4 saved screws and locking

washers (see Figure 2).

8. Connect the green wire with the yellow stripe (Ground)

from the Main terminal block to the Ground screw of the

Magnetek GPD 315. The Ground screw is located just

below the T3 terminal block position of the Magnetek

GPD 315 (see Figure 1).

e l

: 1

p t

t u

t l i

i h

e t

i w

e r

i w

h t

o l

t a

o r

r t

p i

i h

e t

i w

e r

i w

h t

o l

t a

e r

r t

p i

i h

e t

i w

e r

i w

h t

o l

t a

a r

r t

p i

Opti-FloII Upgrade Kit

r e

r i

n i

r e

n i

l a

o i

f o

g i

r e

n i

l a

o i

f o

g i

r e

n i

l a

o i

f o

g i

9. Crimp the two white wires with the yellow stripe from

the existing wire harness into the wire adapter of the

same color (see Figure 1).

10. Crimp the two red wires with the yellow stripe from the

existing wire harness into the wire adapter of the same

color (see Figure 1).

11. Using the new wiring label as a guide install the 3 wires

from the ORIGINAL output filter, white wires with the

brown, red and orange stripes to the proper terminal

locations of the Magnetek GPD 315 (see Figure 1,2

and Table 1).

— IMPORTANT ——————————————––––––––––

Miswiring will cause damage to the Magnetek GPD 315.

e l

: 2

n I

o r

i w

e r

i w

e r

a r

i w

e r

e l

: 3

r i

u l

e r

t r

e l

e r

e l

e r

e l

i h

e t

a r

e r

e l

i h

e t

a r

r t

p i

e r

i h

e t

i h

h t

i v

l o

t e

r t

p i

e r

e l

i h

e t

i v

l o

t e

r t

p i

e r

i h

e t

h t

l e

o l

r t

p i

e r

t u

t l i

r e

r i

n i

o T

r e

n i

l a

o l

t a

o i

f o

h t

i t p

F -

o l

I I

n i

r e

n i

b l

o l

k c

o T

r e

n i

l a

o l

t a

o i

f o

h t

i t p

F -

o l

I I

n i

r e

n i

b l

o l

k c

o T

r e

n i

l a

o l

t a

o i

f o

h t

i t p

F -

o l

I I

n i

r e

n i

b l

o l

k c

e r

a l

, 1

o l

t a

o i

a r

e r

a l

, 1

o l

t a

o i

f o

h t

a r

- i t

o l

I I

n i

e t

n i

l a

o l

f o

h t

- i t

o l

I I

n i

e t

n i

l a

o l

f o

h t

- i t

o l

I I

n i

e r

e t

n i

l a

o l

e t

f o

h t

- i t

o l

I I

n i

e t

n i

l a

o l

h t

e r

a l

e r

, 1

o l

t a

o i

e r

a l

, 1

o l

t a

o i

g i

e r

g i

e r

g i

e r

o i

g i

e r

g i

e r

g i

e r

g i

e r

g i

e r

g i

e r

g i

e r

g i

e r

93-832