CARNES VCDD330I Instrukcja obsługi - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wentylator CARNES VCDD330I. CARNES VCDD330I 4 stron. Inline cabinet fan

Drukuj stronę
Carnes VCDD210I-330I Inline Cabinet Fan
Carnes VCDD210I-330I Inline Cabinet Fan
Operation & Instructions Manual
Operation & Instructions Manual
MOUNTING OPTIONS
MOUNTING OPTIONS
SLEEPER
SLEEPER
1-1/4"
1-1/4"
Typical wall mounting with 3/8" threaded fasteners
Typical wall mounting with 3/8" threaded fasteners
(by others) through mounting brackets.
(by others) through mounting brackets.
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
Connect electrical power cable to housing with proper connector
Connect electrical power cable to housing with proper connector
for type of cable used. Provide 6" leads inside wiring box.
for type of cable used. Provide 6" leads inside wiring box.
MODEL
MODEL
VCDD210I
VCDD210I
SPEED CONTROL
SPEED CONTROL
OR SWITCH
OR SWITCH
WHITE
LINE IN
WHITE
LINE IN
GND
GND
120 VAC
120 VAC
BLK
BLK
60 HZ
60 HZ
MODEL
MODEL
VCDD330I
VCDD330I
SPEED CONTROL
SPEED CONTROL
OR SWITCH
OR SWITCH
LINE IN
LINE IN
RED
RED
240 VAC
240 VAC
GND
GND
60 HZ
BLK
60 HZ
BLK
1 PHASE
1 PHASE
ACCESSORIES
ACCESSORIES
DAMPER
GRILLE
DAMPER
GRILLE
MODEL
KIT
KIT
MODEL
KIT
KIT
VCDD210I
D100
G102
VCDD210I
D100
G102
VCDD330I
D101
G103
VCDD330I
D101
G103
#2 Chootoo Road, South Aranguez, San Juan, Trinidad
®
®
ACCESSORY INSTALLATIONS
ACCESSORY INSTALLATIONS
If ventilator will discharge directly outside, install adamper kit to
If ventilator will discharge directly outside, install adamper kit to
EXHAUST
EXHAUST
prevent backdrafts. A grille kit is available for applications where
prevent backdrafts. A grille kit is available for applications where
ventilator is installed with direct or remote room air intake.
ventilator is installed with direct or remote room air intake.
ACCESS
ACCESS
PANEL
PANEL
CABINET FLUSH
CABINET FLUSH
INTAKE
INTAKE
Snap screw bushings into square openings around intake
Snap screw bushings into square openings around intake
NOTE: If duct flanges around intake opening interfere with installa-
NOTE: If duct flanges around intake opening interfere with installa-
tion, remove them. Make sure that housing is flush with finished
tion, remove them. Make sure that housing is flush with finished
ceiling when ventilator is mounted.
ceiling when ventilator is mounted.
MOTOR
MOTOR
MOTOR
MOTOR
DAMPER BUSHING
DAMPER BUSHING
(Snaps over rod)
(Snaps over rod)
USE AND CARE
USE AND CARE
MOTOR
MOTOR
Ventilator is designed for continuous operation. If desired, it may be
Ventilator is designed for continuous operation. If desired, it may be
controlled using an on/off switch or a solid-state, variable speed
controlled using an on/off switch or a solid-state, variable speed
control. Follow wiring instructions packed with control, and adhere
control. Follow wiring instructions packed with control, and adhere
to all local and state codes, and the National Electrical Code.
to all local and state codes, and the National Electrical Code.
To clean grille: Use appropriate vacuum attachment or remove
To clean grille: Use appropriate vacuum attachment or remove
grille and clean with a soft cloth and mild soap or detergent. Dry
grille and clean with a soft cloth and mild soap or detergent. Dry
grille thoroughly before reinstalling.
grille thoroughly before reinstalling.
To clean blower assembly: Remove either access panel or ceil-
To clean blower assembly: Remove either access panel or ceil-
ing grille. Unplug blower assembly. Provide safe support for blower
ing grille. Unplug blower assembly. Provide safe support for blower
assembly. Remove blower mounting screws and lift blower assem-
assembly. Remove blower mounting screws and lift blower assem-
bly out of housing. Gently vacuum housing and blower motor.
bly out of housing. Gently vacuum housing and blower motor.
Vacuum or gently wash blower wheels and housings. DO NOT AL-
Vacuum or gently wash blower wheels and housings. DO NOT AL-
SPEED
VIBRATION
LOW WATER TO ENTER MOTOR. Make sure blower assembly is
LOW WATER TO ENTER MOTOR. Make sure blower assembly is
SPEED
VIBRATION
CONTROL
HANGER
completely dry before reinstalling. Replace blower assembly in hous-
completely dry before reinstalling. Replace blower assembly in hous-
CONTROL
HANGER
ing and plug assembly in. Replace grille and/or access panel.
72V / 72W
V104
ing and plug assembly in. Replace grille and/or access panel.
72V / 72W
V104
75V
V104
Motor is permanently lubricated. Do not oil or disassemble motor.
75V
V104
Motor is permanently lubricated. Do not oil or disassemble motor.
MODELS • VCDD210I • VCDD330I
MODELS • VCDD210I • VCDD330I
CEILING
CEILING
GRILLE
GRILLE
SCREWS
SCREWS
GRILLE
GRILLE
NUTS
NUTS
opening. Install grille with screws provided.
opening. Install grille with screws provided.
OUTSIDE
OUTSIDE
ROD
ROD
(Inserts into inside bushing)
(Inserts into inside bushing)
Install damper flap using rod provided.
Install damper flap using rod provided.
WARNING: To reduce the risk of electric shock,
WARNING: To reduce the risk of electric shock,
disconnect from power supply before servicing.
disconnect from power supply before servicing.
Page 3
Page 3
DUCT FLANGES
DUCT FLANGES
INSIDE DAMPER
INSIDE DAMPER
BUSHING
BUSHING
(Inside of frame)
(Inside of frame)
DAMPER FLAP
DAMPER FLAP
(Should open freely)
(Should open freely)