KitchenAid 30" (76.2 CM) WALL-MOUNT CANOPY RANGE HOOD Instrukcja instalacji - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Płyta grzewcza KitchenAid 30" (76.2 CM) WALL-MOUNT CANOPY RANGE HOOD. KitchenAid 30" (76.2 CM) WALL-MOUNT CANOPY RANGE HOOD 7 stron. 30” (76.2cm) sealed burner gas slide-in range with self-cleaning thermal/convection oven
Również dla KitchenAid 30" (76.2 CM) WALL-MOUNT CANOPY RANGE HOOD: Instrukcja instalacji (20 strony)

Drukuj stronę

Tools needed for

installation:

flat-blade

screwdriver

or 5/l 6"

hand or electric

drill

wood floor:

l/S" (3 mm) drill bit

concrete/ceramic

floor:

3/16" (4.5 mm)

carbide-tipped

masonry

drill bit

L.P. gas conversion

requires:

pin pick up (claw

attachment)

5/16" nut driver

Parts supplied

for

installation:

2-plastic

anchors

burner grates

and caps

vent cap

L.P. conversion

orifice

spuds kit:

2 x #64 cooktop

2 x #69 cooktop

1 x #65 broil burner

(Bracket

must be securely

mounted

to sub-floor.

Thickness

of flooring

may require

longer screws

anchor

the bracket

to sub-floor.)

Gas supply

requirements

Observe all governing codes and

ordinances.

Fire Hazard

Range must be connected to a regulated

gas supply.

L.P. gas supply must Not exceed a

pressure of 14 inch water column. This

must be checked by a qualified

technician before installing the range.

L.P. gas must not be used unless L.P.

conversion kit has been installed.

Do Not use an open flame to test for

leaks from gas connections.

New, A.G.AJC.G.A.-design-certified,

flexible metal gas line connector should

be used when codes permit.

Failure to follow these instructions

could

result in a fire, explosion or personal

injury.

This installation

must conform with

local codes and ordinances.

In the

absence of local codes installations

must conform with American National Standard,

National Fuel Gas Code ANSI Z223.1-

latest

edition (**, see Panel A) or CAN/CGA-B1 49

latest edition (***, see Panel A) installation

codes.

Input ratings shown on the

serial/rating

plate are for elevations up

to 2,000 feet (609.6 m). For elevations

above 2,000 feet (609.6 m), ratings are reduced

at a rate of 4% for each 1,000 feet (304.8 cm)

above sea level. (Not applicable for Canada.)

This range is equipped for use with

Natural gas. It is design-certified

A.G.A./C.G.A. for Natural and L.P. gas

with appropriate conversion. The model/serial

rating plate, located on the oven frame behind

the drawer, has information on the type of gas

that can be used. If this information does not

agree with the type of gas available, check with

your KitchenAid dealer. Conversion to L.P. gas

requires installation of the kit included in the

parts package. This conversion

must be done

by a qualified technician.

ID.I

Provide a gas supply line of 3/4"

(1.9 cm) rigid pipe to the range

location. A smaller size pipe on long

runs may result in insufficient

gas supply. Pipe-

joint compounds appropriate for use with L.P.

gas must be used. With L.P. gas, piping or

tubing size can be l/2" (1.3 cm) minimum. L.P.

gas suppliers usually determine the size and

materials used on the system.

If local codes permit, a new

A.G.A./C.G.A.

design-certified,

4-5

foot (122 -152.4 cm) long. l/2"

(1.3 cm) or 3/4" (1.9 cm) I.D.,'flexible

metal

appliance connector is recommended

for

connecting this range to the gas supply line. Do

Not kink or damage the flexible tubing when

moving the range. A l/2" (1.3 cm) male pipe

thread is needed for connection to pressure

regulator female pipe threads.

The supply line shall be equipped with

an approved shutoff valve. This valve

should be located in the same room.

but external to the range, and should be in a '

location that allows ease of opening and

closing. Do Not block access to shutoff valve.

If rigid pipe is used

line, a combination

of pipe fittings

must be used to obtain an in-line

connection

to the range. All strains must be

removed from the supply and fuel lines so

range will be level and in line.

The regulator setting must be checked

at a minimum of 1 inch water column

above the manifold oressure. The inlet

pressure to the regulator should be as follows

for operation:

Natural gas:

Manifold pressure - 5 inches

Maximum pressure - 14 inches

L.P. gas:

Manifold pressure - 10 inches

Maximum pressure - 14 inches

(1.

Line pressure testing:

Testing above l/2 psi (gauge)

The range and its individual shutoff

valve must be disconnected

from the gas supply

piping system during any pressure testing of

that system at test pressures greater than l/2

psig (3.5 kPa).

Testing at l/2 psi (gauge) or lower

The range must be isolated from the gas supply

piping system by closing its individual

manual

shutoff valve during any pressure testing of the

gas supply piping system at test pressures

equal to or less than l/2 psig (3.5 kPa).

Electrical

requirements

Electrical Shock Hazard

Electrical ground is required on this

appliance.

Do Not ground to a gas supply pipe.

Do Not modify the power supply cord

plug. If it does not fit the outlet, have a

proper outlet installed by a qualified

electrician.

. Do Not use an extension cord with this

appliance.

Do Not have a fuse in the neutral or

grounding circuit. A fuse in the neutral or

grounding circuit could result in an

electrical shock.

Check with a qualified electrician

if you

are in doubt as to whether the appliance

is properly grounded.

Failure to follow these instructions

could

result in death or serious injury.

If codes permit and a separate grounding

wire is used, it is recommended that a

qualified electrician determine that the

grounding path is adequate.

A 120-volt, 60-Hz, AC-only, 15-ampere, fused

electrical circuit is required. A time-delay fuse or

circuit breaker is recommended.

It is

recommended

that a separate circuit serving

only this appliance be provided.

Electronic ignition systems operate within wide

voltage limits, but proper grounding and polarity

are necessary. In addition to checking that the

outlet provides 120-volt power and is correctly

grounded, the outlet must be checked by a

qualified electrician to see if it is wired with

correct polarity.

The wiring diagram is included in the literature

package. The wiring diagram can also be found

on the back of the range.

Note:

The metal chassis of the range MUST

be earth-grounded

in order for the control panel

to work. If the metal chassis of the range is not

earth-grounded,

NO keypads will operate.

Check with a qualified electrician

if you are in

doubt as to whether the metal chassis of range

is earth-grounded.

Recommended grounding method

For personal safety, this appliance is equipped

with a power supply cord having a 3-prong

grounding plug. To minimize possible shock

hazard, the cord must be plugged into a mating

3-prong, grounding-type

wall receptacle,

grounded in accordance

with the National

Electrical Code, ANSVNFPA 70 -

latest

edition(*,

see Panel A) or CSA Standard C22.1,

Canadian Electrical Code, Part 1, -

latest

edition( ***, see Panel A), and all local codes

and ordinances.

If a mating wall receptacle is

not available, it is the personal responsibility

and

obligation of the customer to have a properly

grounded, 3-prong wall receptacle installed by a

qualified electrician.

power

plug

grounding

prong

3-prong

grounding-type

wall receptacle

Panel B