KitchenAid 30" (76.2 CM) WALL-MOUNT CANOPY RANGE HOOD Instrukcja instalacji - Strona 4

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Płyta grzewcza KitchenAid 30" (76.2 CM) WALL-MOUNT CANOPY RANGE HOOD. KitchenAid 30" (76.2 CM) WALL-MOUNT CANOPY RANGE HOOD 7 stron. 30” (76.2cm) sealed burner gas slide-in range with self-cleaning thermal/convection oven
Również dla KitchenAid 30" (76.2 CM) WALL-MOUNT CANOPY RANGE HOOD: Instrukcja instalacji (20 strony)

Drukuj stronę

Now start...

With range in kitchen.

Remove shipping materials, tape and

protective film from range. Keep

cardboard bottom and shipping base

under range. Remove oven racks and parts

package from inside oven. Remove the back

vent

package from the range top.

cardboard-&?

corners

spacers

Take 4 cardboard corners from the

carton. Stack one cardboard corner

top of another. Repeat with the

other two corners. Place corners lengthwise on

the floor in back of range so corners will

support outer side edges of range as shown.

Personal Injury Hazard

Because of the weight and size of this

range, two or more people are needed to

move and safely install it.

Failure to do so could result in personal

injury.

13.1

Firmly grasp the range and gently lay

it on its back on the cardboard

corners.

14.1

Pull cardboard bottom and shipping

base firmly to remove.

Use an adjustable

wrench to loosen the I

legs

l-112

turns.

16.1

Place cardboard or hardboard in front

of range. Stand range back up onto

cardboard or hardboard.

Remove the outside screws from rear

trim on range. Use screws to attach

back vent to range.

Check the that the type of gas supply

is correct for this range. (See

seriavrating

plate.)

If connecting to L.P. gas, go

to Panel E and

follow range conversion

instructions

for L.P. gas.

If connecting to Natural gas, go

to Step 9.

*To reduce the risk of tipping the

appliance, the appliance must be

secured by a properly installed floor-

mounted anti-tip bracket supplied with

the range.

Save these Installation

Instructions.

range is moved to a new location, the

anti-tip bracket must be removed and

reinstalled in the new location.

Electrical Shock Hazard

*Take special care when drilling holes

into the floor. Electrical wires or

plumbing may be located beneath the

floor.

Locate the electrical circuits that could

be affected by the installation

of this

bracket and turn off power to these

circuits.

Failure to follow these instructions

may

result in death or serious injury.

anti-tip

bracket

template

Place the anti-tip bracket template for

slide-in ranges

on the floor in the

cabinet opening so that the lefl edge

is against cabinet and the top edge is against

the rear wall, molding or cabinet. If countertop

is deeper than 25 inches (63.5 cm), measure

and mark a distance 25 inches (63.5 cm) in

from front of

countertop opening

and align

template with mark (or subtract 25 inches

(63.5 cm) from the countertop depth and add

the difference to the 2-l/4" (5.7 cm) dimension).

Countertop

overhangs

cabinet

side.

A = Difference

between

countertop

depth and

25" (63.5 cm).

If countertop

is not flush to the side of the

cabinet opening, align the left side of the

template to allow for the countertop overhang.

Tape the slide-in range anti-tip bracket template

in place.

Property Damage

Contact a qualified floor covering

installer for the best procedure of drilling

mounting holes through your type floor

covering.

Before moving, slide range onto

cardboard or hardboard.

Failure to do so may result in damage to

floor covering.

To mount

anti-tip

bracket to

wood floor,

use the

anti-tip bracket

template to mark where

to drill mounting holes.

Use a drill with a l/8"

(3 mm) drill bit to drill

the two mounting

holes. Remove

template from floor.

To mount anti-tip bracket to concrete or

ceramic floor,

use the anti-tip bracket template

to mark where to drill mounting holes. Use a

drill with a 3/16" (4.5 mm) masonry drill bit to

drill the two holes. Remove template from floor.

Tap plastic anchors into mounting holes in floor

with hammer.

Line up holes in

anti-tip bracket

with mounting

holes in floor. Use the

screws provided to fasten

anti-tip bracket to floor.

NOTE: Anti-tip bracket

must be mounted

securely to the sub-floor.

Depending on the

thickness of your flooring, longer screws may

be necessary to anchor the bracket to the sub-

floor. Longer screws are available from your

local hardware store.

1121

Move range close to cabinet

opening. Remove cardboard or

. hardboard from under range.

Press on front

release to open. Pull open

to first stoo oosition. Lift

front of dr&er

to clear

white wheels in drawer guides. Remove drawer

and set it aside on a protected surface.

1141

Carefully move

range into final

' position. Look

under range (a flashlight

may be needed) to check

that left rear leveling leg is

engaged in the anti-tip

bracket. If leveling leg is not properly engaged,

remove and reposition the anti-tip bracket to

insure that the leveling leg fits properly in the

anti-tip bracket.

1151

Place rack

in oven.

Place level

on rack, first side to

side; then front to back.

If the range is not level,

pull range forward until

the rear leveling leg is removed from the anti-tip

bracket. Adjust the leveling legs up or down.

Then slide range back into position. Check that

leveling leg is engaged in ant-tip bracket.

NOTE: Oven must be level for satisfactory

baking conditions.

Fire Hazard

Do Not make connection too tight. The

regulator is die cast.

Overtightening

may crack the regulator,

resulting in a gas leak and possible fire

or explosion.

All connections

must be wrench-tightened.

pressure

regulator

and valve assembly

flexible

manual

co:nector

shutoff

valve

l/2" (1.3 Em) flare union adapters

(16.1

Assemble the flexible connector

from the gas supply pipe to the

pressure regulator, located in the

lower lefl side of the storage drawer area, in

this order: shutoff valve, l/2" flare union

adapter, flexible connector, l/2" flare union

adapter. Seal all openings in floor or wall

wherever range is installed.

1171

Use pipe-joint compounds

appropriate for use with L.P. gas to

. seal all gas connections.

If flexible

connectors are used, be certain connectors are

not kinked.

1181

Open shutoff valve in gas supply

line. Wait a few minutes for the gas

. to move through gas line.

Fire Hazard

Do Not use an open flame to test for

leaks from gas connections.

Checking for leaks with a flame may

result in a fire or explosion.

Use a brush and liquid detergent to

test all gas connections

for leaks.

Bubbles around gas connections

will indicate a leak. If a leak appears, shut off

gas valve controls and adjust connections.

Then check connections

again.

NEVER TEST

FOR GAS LEAKS WITH A MATCH OR

OTHER FLAME.

Clean all detergent solution

from range.

Panel C