KitchenAid 30" (76.2 CM) WALL-MOUNT CANOPY RANGE HOOD Instrukcja instalacji - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Płyta grzewcza KitchenAid 30" (76.2 CM) WALL-MOUNT CANOPY RANGE HOOD. KitchenAid 30" (76.2 CM) WALL-MOUNT CANOPY RANGE HOOD 7 stron. 30” (76.2cm) sealed burner gas slide-in range with self-cleaning thermal/convection oven
Również dla KitchenAid 30" (76.2 CM) WALL-MOUNT CANOPY RANGE HOOD: Instrukcja instalacji (20 strony)

Drukuj stronę

Numbers

correspond

steps.

ignitor

/db I&

Plug power supply cord into

grounded outlet. "8888" should

appear in clock display. Refer to Use

and Care Guide for information on electronic

controls.

1211

Remove vent cap, cooktop burner

, caps and grates from parts

package. Align notches in burner

caps with pins in burner base. Burner caps

should be level when properly positioned.

Place

burner grates over burners and caps. Place

vent cap over vent.

Electronic Ignition System -

Initial lighting and gas flame adjustments.

Cooktop and oven burners use electronic

ignitors in place of standing pilots. When the

cook-top control knob is turned to the "HI"

position, the system creates a spark to light the

burner. This sparking continues until the burner

has a flame. When the oven control is turned to

the desired setting, a glow bar heats up bright

orange and ignites the gas. No sparking occurs

and the glow bar remains on while the burner

operates.

cook-top burners.

Push in and turn each

control knob to the

"HI" position. The

flame should light

within 4 seconds. The

first time a burner is

lighted it may take

longer than 4 seconds

to light because of air

in gas line.

OFF

(23

If burners do not light properly, turn

cooktop control knob to the "OFF"

position. Check that the power

supply cord is plugged in and the circuit breaker

has not tripped or fuse blown. Check that the

gas shutoff valves are set to the "OPEN"

position. Repeat Step 22. If a burner does not

light at this point, contact your KitchenAid dealer

or authorized

service company for assistance.

Panel D

124)

Check each cooktop burner for

proper flame. At the "HI" setting, the

small inner cone should have a very

distinct blue flame approximately

l/2" (1.3cm)

long. The outer cone is not as distinct as the

inner cone.

Push in and turn the control knob to the "LO"

position. The low flame should be a minimum,

steady, blue flame. The "LO" (or simmer) setting

of each burner has been factory set to the

lowest setting available to provide reliable

reignition of the burner. If any burner does not

stay lit on the "LO" setting, contact your

KitchenAid dealer or authorized service

company for assistance.

Remove the oven rack. Remove the

oven bottom and place it on a

protected surface.

Control

consoles

vary with models.

(26

Check the operation of the oven

burner. Push the "BAKE" pad and

"350°F' will appear in the

temperature display. Press the "Stat-t" pad. "LO"

will appear in the display; then "17O'FI'

The oven

burner should light in 50 to 60 seconds. This

delay is normal.

The oven safety valve requires

a certain time before it will open and allow gas to

flow.

Product Damage

Electric ignitors are used to light the

oven and broil burners. Do Not insert any

object into the opening of the protective

shield that surrounds the ignitor.

Do Not clean the area.

Failure to follow these instructions

could

result in product damage.

(27.(

Check the oven burner

for proper flame. This

flame should have a l/2"

(1.3 cm) long inner cone of bluish-

green, with an outer mantle of dark

blue, and should be clean and soft in

character. No yellow tips, blowing or

lifting of flame should occur.

locking

screw

oven burner

air shutter/

-\n

-hood

128

If the oven flame needs to be

adjusted, locate the air shutter near

the center rear of range. Loosen the

locking screw and adjust the air shutter until the

proper flame appears. Tighten screw.

Push "Cancel/Off"

pad. Replace the

oven bottom and oven racks.

Check the operation of the

oven broil burner. Close the oven

door. Press the "BROILI' pad.

"5OO'F" will appear in the temperature

display.

Press the "Start" pad.

The oven broil burner

should light in 50 to 60 seconds. This delay

is normal.

The oven safety valve requires a

certain time before it will open and allow gas to

flow. The first time the broil burner is lighted, it

may take longer to light because of air in gas

line. The first few times the broil burner is used

sparks may appear. This is normal.

NOTE: Oven door must be shut for broil burner

to operate.

131)

Look through oven window to check

broil burner for proper flame. The

flame should have a uniform, light

blue appearance

around the burner surface. No

yellow tips, blowing or lifting of the flame should

occur.

NOTE:The first few times the broil burner is

used, yellow sparks may appear in the flame.

This is normal and will stop after burner has

been used a few times.

1321

Press the "Cancel/Off"

pad. If the

broil burner flame needs

adjustment, contact your KitchenAid

dealer or authorized

service company for

assistance.

133

Insert

storage

drawer

into slide rails on

sides of drawer

opening. Lift front of

drawerslightly

and

push firmly to close drawer.

To get the most efficient use

from your new range,

read your Use and Care Guide.

Keep Ins talla tion Ins true tions

and Guide close to range

for easy reference.