Cisco Versatile Interface Processor (VIP6-80) (VIP6-80) Instrukcja instalacji i konfiguracji - Strona 29

Przeglądaj online lub pobierz pdf Instrukcja instalacji i konfiguracji dla Sprzęt sieciowy Cisco Versatile Interface Processor (VIP6-80) (VIP6-80). Cisco Versatile Interface Processor (VIP6-80) (VIP6-80) 40 stron. Versatile interface processor

Cisco Versatile Interface Processor (VIP6-80) (VIP6-80) Instrukcja instalacji i konfiguracji
Using show Commands to Display Interface Information
This section describes using show commands to display interface information.
To display information about a specific interface, use the show interfaces command with the interface
type and interface address in the format show interfaces type interface-processor-slot-
number/port-adapter-slot-number/interface-port-number.
With the show interfaces command, use arguments such as the interface type and the interface address
to display information about a specific interface only. The following example of the
show interfaces fastethernet command shows information specific to a VIP6-80 with a Fast Ethernet
port adapter (PA-2FE) installed; the VIP6-80 is installed in interface processor slot 1:
Router# show interfaces fastethernet 1/0/0
FastEthernet1/0/0 is up, line protocol is up
Hardware is cyBus FastEthernet Interface, address is 0000.0c4c.8820 (bia 0000.0c4c.8820)
Internet address is 192.168.36.4/28
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type:ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 01:25:25
Queueing strategy:fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 1271000 bits/sec, 251 packets/sec
5 minute output rate 470000 bits/sec, 83 packets/sec
To display hardware information about all of the interface processors in your router, including the
VIP6-80, use the show controllers cbus command.
Following is an example of the show controllers cbus command used with a Cisco 7500 series router:
Router# show controllers cbus
slot1:VIP6 RM7000B, hw 2.00, sw 22.20, ccb 5800FF30, cmdq 48000088, vps
8192
12.0(20020228:202448) [mssunil-vip6-conn_is
slot4:VIP6 RM7000B, hw 2.03, sw 22.20, ccb 5800FF60, cmdq 480000A0, vps
OL-5078-01
1703680 packets input, 532380667 bytes, 0 no buffer
Received 4008 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast
0 input packets with dribble condition detected
566766 packets output, 260633463 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
software loaded from system
IOS (tm) VIP Software (SVIP-DW-M), Experimental Version
ROM Monitor version 103.0
POS1/0/0, applique is SONET
gfreeq 48000178, lfreeq 480001C8 (4544 bytes)
rxlo 4, rxhi 132, rxcurr 4, maxrxcurr 5
txq 48001A80, txacc 48001A82 (value 63), txlimit 63
FastEthernet1/1/0, addr 0050.739f.cd28 (bia 0050.739f.cd28)
gfreeq 48000158, lfreeq 480001D0 (1536 bytes)
rxlo 4, rxhi 161, rxcurr 4, maxrxcurr 5
txq 48001A88, txacc 48001A8A (value 61), txlimit 61
Versatile Interface Processor (VIP6-80) Installation and Configuration Guide
29