Cisco Versatile Interface Processor (VIP6-80) (VIP6-80) Instrukcja instalacji i konfiguracji - Strona 30
Przeglądaj online lub pobierz pdf Instrukcja instalacji i konfiguracji dla Sprzęt sieciowy Cisco Versatile Interface Processor (VIP6-80) (VIP6-80). Cisco Versatile Interface Processor (VIP6-80) (VIP6-80) 40 stron. Versatile interface processor
Drukuj stronę
To display hardware information about a specific interface on a VIP6-80 port adapter, append the type
argument (fastethernet, hssi, and so forth) and the interface address argument
(interface-processor-slot-number/port-adapter-slot-number/interface-port-number) to the
show controllers command.
Following is an example of the syntax for this command for the interface on a PA-2FE port adapter
installed in port adapter slot 1 of a VIP6-80 installed in interface processor slot 1 of a Cisco 7000 series
or Cisco 7500 series router:
Router# show controllers fastethernet 1/1/0
To display the configuration of the system hardware (the number of each interface processor type
installed), the software version, the names and sources of configuration files, and the boot images, use
the show version (or show hardware) command.
Following is an example of the show version command used with a Cisco 7500 series router:
Router# show version
Cisco Internetwork Operating System Software
IOS (tm) RSP Software (RSP-JSV-M), Version 12.0(10r)S1, EARLY DEPLOYMENT
MAINTENANCE INTERIM SOFTWARE
TAC Support:http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 22-Mar-02 16:27 by ninahung
Image text-base:0x60010950, data-base:0x612A2000
ROM:System Bootstrap, Version 12.0(10r)S1, RELEASE SOFTWARE (fc1)
UUT uptime is 2 minutes
System returned to ROM by reload at 15:33:45 UTC Tue Mar 5 2002
System image file is "disk0:rsp-pv-mz.vip6-3.022802"
cisco RSP4+ (R5000) processor with 65536K/2072K bytes of memory.
R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache
Last reset from power-on
G.703/E1 software, Version 1.0.
G.703/JT2 software, Version 1.0.
X.25 software, Version 3.0.0.
1 VIP6 RM7000B controller (2 FastEthernet).
1 GEIP controller (1 GigabitEthernet).
2 FastEthernet/IEEE 802.3 interface(s)
1 Gigabit Ethernet/IEEE 802.3 interface(s)
123K bytes of non-volatile configuration memory.
47040K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
16384K bytes of Flash internal SIMM (Sector size 256K).
No slave installed in slot 7.
Configuration register is 0x0
WARNING:Chassis Interface not present
To determine specific hardware configuration information about a VIP6-80 installed in your system
(including the amount of installed CPU and packet memory), use the show diag slot command.
Specific information is displayed, as shown in the following example of a VIP6-80 with a PA-2FE port
adapter; the VIP6-80 is installed in interface processor slot 4:
Router# show diag 4
Slot 4:
Versatile Interface Processor (VIP6-80) Installation and Configuration Guide
30
Physical slot 4, ~physical slot 0xB, logical slot 4, CBus 0
Microcode Status 0x4
Master Enable, LED, WCS Loaded
Board is analyzed
Pending I/O Status:None
OL-5078-01