Epson 7850p - PowerLite XGA LCD Projector Podręcznik z informacjami o produkcie - Strona 15

Przeglądaj online lub pobierz pdf Podręcznik z informacjami o produkcie dla Oprogramowanie Epson 7850p - PowerLite XGA LCD Projector. Epson 7850p - PowerLite XGA LCD Projector 25 stron. Release of check tool for network projectors v1.00 for windows
Również dla Epson 7850p - PowerLite XGA LCD Projector: Podręcznik użytkownika (42 strony), Instrukcja obsługi (36 strony), Podręcznik użytkownika (12 strony), Części zamienne (1 strony), Instrukcja obsługi (47 strony), Biuletyn wsparcia produktu (30 strony), Instrukcja instalacji (5 strony), Szybka konfiguracja (2 strony), Broszura i specyfikacje (2 strony), Streszczenie techniczne (7 strony), Biuletyn wsparcia produktu (25 strony), Biuletyn wsparcia produktu (38 strony), Biuletyn wsparcia produktu (12 strony), Biuletyn wsparcia produktu (42 strony), Biuletyn wsparcia produktu (22 strony), Biuletyn wsparcia produktu (28 strony), Biuletyn wsparcia produktu (41 strony), Biuletyn wsparcia produktu (34 strony), Biuletyn wsparcia produktu (38 strony), Biuletyn wsparcia produktu (28 strony), Biuletyn wsparcia produktu (15 strony), Biuletyn wsparcia produktu (22 strony)

Drukuj stronę
Epson 7850p - PowerLite XGA LCD Projector Podręcznik z informacjami o produkcie
EPSON PowerLite 7850p Projector
3. Click the
button. Then click the
Configure
on the screen that appears. You see a screen like this:
4. Ad Hoc mode: Highlight
list and set the Value to
Access Point mode: Highlight
Value to
Infrastructure
5. Ad Hoc mode: Highlight
the name you gave the projector's ESSID (for example,
). If your network card uses channel mode
CONF ROOM
instead, set the correct channel, 1 to 11, to match that of
the projector.
Access Point mode: Highlight
match the name assigned to the access point.
6. Highlight
Encryption
7. Click the
tab and make sure the network card or
General
wireless network device is enabled.
8. Ad Hoc mode: Click
OK
properties dialog box. Then go to "Projecting Wirelessly"
on page 15.
Access Point mode: On the General tab, select
, then click the
Protocol
screen:
14
EPSON PowerLite 7850p Projector
-
Advanced
in the Property
Network Type
.
802.11 Ad Hoc
and set the
Network Type
.
and set the Value to match
SSID
and set the Value to
SSID
and make sure it is disabled.
to close the network card's
Internet
button. You see this
Properties
tab
9. If your access point uses DHCP, select
automatically
and enter the required information.
address
❏
IP address
to the computer. It must be formatted like other
addresses on the network; usually the first three
segments (XXX.XXX.XXX) match the access point's IP
address.
❏
Subnet mask
this too must match how your network was set up.
❏
Default gateway
assigned to the access point when it was set up.
10. When done, click
11. Click the
Wireless Networks
Note: If you don't see this tab, you may need to enable your
wireless card or network device by clicking
access the device settings; then follow any instructions on the
screen to enable the device.
6/03
Obtain IP address
. Otherwise, select
Use the following IP
: Type in the IP address you want to assign
: For example, 255.255.255.000, but
: Enter the IP address that was
.
OK
tab. You see this screen:
to
Configure