Draper Patriot Motorized Flag 500101 Manual de instruções - Página 3
Procurar online ou descarregar pdf Manual de instruções para Mobiliário de interior Draper Patriot Motorized Flag 500101. Draper Patriot Motorized Flag 500101 8 páginas.
Imprimir página
Patriot Motorized Flag
Section 1 - Hanging Motorized Flag
Section 1.1 - Ceiling Installation
PLEASE NOTE:
It is the installer's responsibility to make sure appropriate fasteners are
used for mounting.
1. Engage each case mounting bracket
tighten set screws.
2. Flag should be sufficiently supported to withstand vibration.
Please Note: A hoisting bracket is included on each end of the case to aid in installation.
Hoisting bracket is NOT TO BE USED for final installation, only to hoist the case up to
the mounting location.
3. Ensure that fasteners are of adequate strength and suitable for the mounting surface
chosen. Supporting hardware such as chains, cables, two 3/ 8 "
be precisely vertical.
4. Entire bottom of case must be readily accessible after installation is complete.
5. Front, back, and top of case must be straight—not forced to warp or bow.
CAUTION: Flag case and flange are not designed to serve as ceiling support.
6. Do not seal unit in ceiling until electrical connections have been made and flag
operates successfully.
Suspended Ceiling Installation—
Chains should be attached to solid beams or rafters above unit.
If possible, mounting brackets should be positioned so chains hang vertically.
Turnbuckles should be connected between chains and mounting brackets.
After the unit has been suspended, turnbuckles should be adjusted so that flag hangs level.
Recessed Ceiling Installation—
Recess should be constructed to fit case with brackets
Design recess so that entire bottom of case is unobstructed to permit access to bottom panel,
roller and flag for servicing if required.
Section 1.2 - Wall Installation
Wall Brackets should fasten to studding or other structural supports within wall that are
capable of supporting weight of case
1. Remove each ceiling mounting bracket
replace with the wall mounting brackets, and tighten set screws.
2. Case should be sufficiently supported to withstand vibration.
Please Note: A hoisting bracket is included on each end of the case to aid in installation.
Hoisting bracket is NOT TO BE USED for final installation, only to hoist the case up to
the mounting location.
3. Ensure that fasteners are 3/ 8 "
(21mm)
for the mounting surface chosen.
4. Entire bottom of case must be readily accessible after installation is complete.
5. Front, back, and top of case must be straight—not forced to warp or bow.
CAUTION: Screen case and flange are not designed to serve as ceiling support.
6. Do not seal unit until electrical connections have been made and screen operates
successfully.
with top of housing
(attached to case)
(9.5 mm)
H O
(see "Case Dimensions" on pages 6-7)
TYPICAL
CEILING
INSTALLATION
With typical installation, brackets
may be angled to meet installation requirements.
.
(205 lbs)
from top of housing
(attached to case)
in diameter, are of adequate strength and suitable
and
(Fig. 1)
H O
rods, etc., must
TYPICAL
CEILING
INSTALLATION
With typical installation, brackets
may be angled to meet installation requirements.
HOISTING BRACKET
not to be used for
final installation
CASE
⁄
"
MOUNTING
(22mm)
BRACKET
CABLE
EXIT
U S
I N G
.
Figure 2
HOISTING BRACKET
(Fig. 2)
H O
TYPICAL
WALL
INSTALLATION
Figure 1-A
HOISTING BRACKET
not to be used for
final installation
CASE
MOUNTING
BRACKET
U S
I N G
HOISTING BRACKET
not to be used for
final installation
H O
U S
I N G
ALTERNATE
CEILING
INSTALLATION
Additional set of brackets
required, but NOT included.
PLEASE NOTE:
responsibility to make sure
appropriate fasteners are
used for mounting.
not to be used for
final installation
WALL
MOUNTING
BRACKET
U S
I N G
page 3 of 8
⁄
"
(22mm)
CABLE
EXIT
Figure 1-B
TWO CASE
MOUNTING
BRACKETS
Per End
It is the installer's
⁄
"
(22mm)
CABLE
EXIT